Fayat DYNAPAC CC1400C Скачать руководство пользователя страница 84

Страница: 84 / 239

Operation

4812164601_C.pdf

2023-01-05

Driver seat - Adjustment

Adjust the operator’s seat so that the position is
comfortable and so that the controls are within
easy reach.

The tables below show the adjustments that can be
made on the different seats.

The image below to the left shows a fully equipped
luxury comfort seat while the image below to the right
shows a normally equipped comfort seat.

Always make sure that the seat is secure before
beginning operation.

Remember to use the seat belt (9).

Fig. Driver seat (MSG65)
1. Locking lever - Length adjustment
2. Weight adjustment
4. Backrest inclination
9. Seat belt

Fig. Driver seat (MSG20)
1. Locking lever - Length adjustment
2. Weight adjustment
4. Backrest inclination
9. Seat belt

Length
adjustment (1)

Weight
adjustment (2)

Side travel (3)

Backrest
inclination (4)

Length
adjustment (1)

Weight
adjustment (2)

Side travel (3)

Backrest
inclination (4)

Standard seat

Comfort seat

(Optional)

Comfort seat

(Optional)

Luxury comfort seat

(Optional)

Luxury comfort seat

(Optional)

Содержание DYNAPAC CC1400C
















































































































































































































































Результаты поиска

Содержание DYNAPAC CC1400C

Отзывы:

Fayat DYNAPAC CC1400C, Инструкция по эксплуатации, Страница: 84 / 239

Результаты поиска

Содержание DYNAPAC CC1400C

Отзывы: