Fayat DYNAPAC CC1400C Скачать руководство пользователя страница 230

Страница: 230 / 239

Maintenance, 3000h

4812164601_C.pdf

2023-01-05

Hydraulic reservoir - fluid change

Fig. Hydraulic reservoir
1. Draining

Use an external drainage pump when
draining/emptying the hydraulic reservoir.

Risk of burn injuries when draining hot oil.
Wear protective gloves and goggles.

Unscrew the tank cap. Place the pump's suction hose
in the filler/drain outlet in the hydraulic tank. Place the
other hose in a container.

Use a receptacle that holds at least
42 liters (11 gal).

Start the pumpen so that it sucks out the fluid
from the tank.

Check that the hose to the pump reaches the bottom
of the hydraulic reservoir to ensure that as much of the
fluid as possible is drained.

Collect the oil and deliver to
special waste handling.

Fill up with the recommended hydraulic fluid to the
correct level. Replace the cap on the tank and
wipe clean.

Change the hydraulic fluid filter. See under heading
'Every 1000 hours of operation'.

Start the engine and operate the various hydraulic
functions. Check the level in the reservoir and top
off as required.

214

Содержание DYNAPAC CC1400C
















































































































































































































































Результаты поиска

Содержание DYNAPAC CC1400C

Отзывы:

Fayat DYNAPAC CC1400C, Инструкция по эксплуатации, Страница: 230 / 239

Результаты поиска

Содержание DYNAPAC CC1400C

Отзывы: