manualshive.com logo in svg

FastVision FastCamera13, Руководство пользователя, Страница: 25 / 52

Поделиться
Скачать
FastVision FastCamera13 Скачать руководство пользователя страница 25

 

25

This is the only Control FPGA response that uses binary encoded arguments (with escape codes for <cr> 
and \). 

The camera responds with “M” followed by escaped binary data from the flash and finally a non-escaped 
carriage-return.  Internally the Control FPGA waits for the flash to become non-busy then starts the flash 
read operation.  Thus the Status Register Read command is only useful to check the compare flag, since 
the busy flag will always be off. 

N - Set Camera State 

This command takes a two byte (4 hex digit) offset into the current camera state as defined in Table 4 and 
from one to to 512 bytes (2 to 1024 hex digits) of camera state data.  The exact syntax of the Set Camera 
State command is: 

‘N’ <addr> <data> <cr> 

where <addr> is 4 hex digits of offset per Table 4 and <data> is 2 to 1024 hex digits (always a multiple of 2) 
of data which will be stored sequentially into the current camera state as shown in Table 4.  Actual registers 
affected by the command are updated as the data comes in, except where further synchronization is 
required such as multibyte values and values that change only between frames.  The Control FPGA always 
responds with “N” followed by a carriage-return even if the affected state is handled by the Data or DDR 
FPGAs.  If the baud rate is changed, the command response happens at the original baud rate. 

O - Serial Trigger 

This command takes no arguments.  This command has the same effect as pulsing the CC1 line high for 
the time period between receipt of the ‘O’ and receipt of the carriage-return.  Although this command would 
normally be used only in edge-triggered mode, it can also be used in external exposure mode for long 
exposures (minimum exposure is limited by the serial baud rate).  To support this mode, any characters 
between the “O” and the <cr> are ignored.  Thus the total command length in characters can be used to 
determine the exposure time.  The camera responds with “O” followed by a carriage-return. 

P - Reset and Calibrate Sensor 

This command takes no arguments.  It causes the sensor’s LRST_N signal to be pulsed low for two clock 
cycles.  The sensor is reset and performs an auto-calibration.  This command is applied by the readout 
logic between frames. If enabled, the CC4 line will also initiate this command allowing operation without the 
GUI.  The camera responds with “P” followed by a carriage-return. 

X - Send Initialization Data to Data FPGA 

This command takes any number of bytes (even number of hex digits) of FPGA initialization data.  The 
exact syntax of the Send Initialization Data command is: 

‘X’ <data> <cr> 

where <data> is an even number of hex digits of data which can be used for any function required by the 
Data FPGA.  This command is sent by the Control FPGA to the Data FPGA upon power-on initialization 
and after the ‘J’ command (Initialize FPGA from Flash).  It is also possible for the host to issue this 
command via the Camera Link serial interface, but be aware that the Data FPGA does not issue a 
response. 

Y - Readout Image 

This command takes no arguments. This command is only effective in the memory readout modes.  If 
enabled, the CC2 line will also initiate this command allowing operation without the GUI.  The Data FPGA 
will respond with “Y” followed by a carriage-return. 

Z - Reset Memory 

This command takes no arguments.  This command is only effective in the memory readout modes.  If 
enabled, the CC3 line will also initiate this command allowing operation without the GUI.  The Data FPGA 
will respond with “Z” followed by a carriage-return. 

17. INTER-FPGA 

COMMUNICATION 

Содержание FastCamera13





















































Отзывы:

Нет отзывов