EZ-ACCESS PATHWAY 3G SS06VP Скачать руководство пользователя страница 67

Страница: 67 / 74

Page 67 of 74

7.7.

TIE DOWN

The PTDK (TIE DOWN KIT) includes a pair of auger style anchors for mounting the system in soil or

through asphalt, plus wire rope and hardware needed to attach the ramp or platform to the

anchor. The tie down is designed to anchor the system to resist seismic loading and hurricane

strength winds, but is not rated for specific soil conditions or seismic zones. Compliance with

local building codes usually requires anchoring calculations for the specific location, ground

condition, and system stamped by a professional engineer. Consult your sales representative if

site specific stamped calculations are required.

Prior to installing the auger anchors into the ground, ensure that any underground

electrical conductors, natural gas lines, water/drain lines, and/or other interferences are

located and will not hinder the installation.

Inspect installation regularly for any loose wire ropes, fasteners, auger anchors, etc.

Do not use concrete anchors in asphalt. Asphalt is not usually considered a suitable surface

for anchoring. Create holes in the asphalt and anchor the system to the ground using auger

style anchors.

The installer, based on field conditions, will determine the exact location of the tie downs. As a

general rule, they should be positioned opposite one another as shown (FIG. 7.10)

Install the PATHWAY 3G Modular Access System to establish layout and locations. It may be

necessary to temporarily reposition components in order to install the anchors.

FIG. 7.10

Содержание PATHWAY 3G SS06VP











































































Результаты поиска

Содержание PATHWAY 3G SS06VP

Отзывы:

Похожие инструкции для PATHWAY 3G SS06VP

Бренды по названию

Популярные бренды

EZ-ACCESS PATHWAY 3G SS06VP, Инструкция по сборке

Результаты поиска

Содержание PATHWAY 3G SS06VP

Отзывы:

Похожие инструкции для PATHWAY 3G SS06VP

Бренды по названию

Популярные бренды