EZ-ACCESS PATHWAY 3G SS06VP Скачать руководство пользователя страница 13

Страница: 13 / 74

Page 13 of 74

2.2.

INSTALL SUPPORT TUBES AND FEET, THEN ADJUST PLATFORM HEIGHT

2.2.1.

Support tubes, plugs, and feet come in pairs. Support tubes will come in lengths

sufficient for the heights at specific locations.

2.2.2.

Loosen all set screws in the platform corner pockets.

2.2.2.1

The set screws on the outside of the platform are for the platform support

tubes.

2.2.2.2. The set screws on the inside of the platform (one above the deck and one

below the deck) are for the handrail posts.

2.2.3.

Tip the platform on its side, then slide the support tubes into the four platform corner

pockets. Adjust the support tubes to the approximate platform height needed (FIG.2.5).

FIG. 2.5

2.2.4.

Use supplied 3/16

″

Allen wrench to tighten the upper of the two set screws in the

corner pocket, just enough to hold the support tube in place but do not over tighten

(the second set screw will be tightened after final height adjustments are complete).

Platforms configured as a turn back platform (FIG. 2.3) will have six tubes to

adjust.

Do not attempt to walk on the platform until all support tube set screws have

been tightened securely.

2.2.5.

Place the platform (with support tubes attached) into the upright position.

Do not let the weight of the platform bear on the support tubes while tipping

the platform upright.

2.2.6.

Lift each corner of the platform and install a base foot on each support tube oriented

so that the foot extends under the platform (FIG. 2.5).

Содержание PATHWAY 3G SS06VP











































































Результаты поиска

Содержание PATHWAY 3G SS06VP

Отзывы:

Похожие инструкции для PATHWAY 3G SS06VP

Бренды по названию

Популярные бренды

EZ-ACCESS PATHWAY 3G SS06VP, Инструкция по сборке

Результаты поиска

Содержание PATHWAY 3G SS06VP

Отзывы:

Похожие инструкции для PATHWAY 3G SS06VP

Бренды по названию

Популярные бренды