EZ-ACCESS PATHWAY 3G SS06VP Скачать руководство пользователя страница 42

Страница: 42 / 74

Page 42 of 74

4.9.18.

For the “long” side of the 45° Angle Platform there are two welded Vertical Picket

panels which are inserted into the corner pockets then bolted together. Left hand

and right hand refer to looking at the “long” side from the “short” side. Insert both

into their respective corner pockets and align the bottom of the posts with the

bottom of the corner pockets. Bolt the two sections together using 5/16”-18 x 1” hex

bolts, 5/16” flat washers and 5/16”-18 nuts as shown (FIG 4.23). Tighten the set

screws in the corner pockets securely and install angle caps on top of the posts.

4.9.19.

Refer to SECTION 4.6 for installing platform handrails and attaching angle caps.

FIG. 4.23

4.9.20.

Install an adjustable elbow in the ramp handrail closest to the right hand Vertical

Picket panel and a 1-1/2” diameter handrail tube to this elbow. Set the Handrail

Support Bracket so it is centered over the picket shown and set the 1-1/2” diameter

handrail tube in the saddle of the bracket (but do not attach) then trim the handrail

tube so that a second adjustable elbow will align (approximately) with the split

between the Vertical Picket panels (FIG. 4.24). The procedure for installing the 1-1/2”

diameter handrail tubes and adjustable elbows is the same as the installing the

closure top rail.

FIG. 4.24

Содержание PATHWAY 3G SS06VP











































































Результаты поиска

Содержание PATHWAY 3G SS06VP

Отзывы:

Похожие инструкции для PATHWAY 3G SS06VP

Бренды по названию

Популярные бренды

EZ-ACCESS PATHWAY 3G SS06VP, Инструкция по сборке

Результаты поиска

Содержание PATHWAY 3G SS06VP

Отзывы:

Похожие инструкции для PATHWAY 3G SS06VP

Бренды по названию

Популярные бренды