EZ-ACCESS PATHWAY 3G SS06VP Скачать руководство пользователя страница 50

Страница: 50 / 74

Page 50 of 74

5.6.

VERTICAL PICKET CLOSURE

5.6.1.

Vertical Picket closures are specific to the platform size (4’, 5’ and 6’) and come in

two pieces which allow the ramp to be mounted to one side or be centered on a

platform side. If the ramp is to be centered on a platform additional components are

needed. The additional components will come with the closure if specified at the

time of order but the closure can be converted to allow the ramp to be centered in

the field by ordering a second set of hardware. Locate the correct Vertical Picket

closure for the platform.

5.6.2.

Bolt the two Vertical Picket closure sections together using 5/16”-18 x 3/4” long hex

bolts, 5/16” flat washers, and 5/16”-18 nuts (as shown in FIG 5.13). Then, Insert 1-

1/4” square tube plugs in the open ends of the top and bottom rails on one side. If

the ramp will be centered, do not assemble. Insert 1-1/4” square tube plugs in all

open ends which do not attach to a platform post.

The 4’ closure includes angles (rather than channels) on one side to allow access

to the assembly fasteners. Always bolt the 4’ closure together using the side

with the angles and attach the side with the channel to the platform post (FIG.

5.14).

FIG. 5.13

FIG. 5.14

5.6.3.

Attach the Vertical Picket closure to the platform handrail post using 5/16”-18 x 3/4”

long hex bolts, 5/16” flat washers and 5/16”-18 nuts as shown (FIG. 5.15). When

centering the ramp attach one section (unassembled) to the platform posts on both

sides of the ramp and secure in the same manner.

5.6.4.

Locate the platform closure brackets and attach the short leg of the brackets to the

ramp post with 5/16″

-18 x 2-

1/4″ hex bolts, 5/16” flat washers and 5/16″

-18 nuts

using the holes (FIG. 5.16). Orient the bracket so the long leg is on the same side as

and parallel to the Vertical Picket closure then tighten lightly (enough to hold the

bracket against the post but still allow it to rotate).

5.6.5.

Install a 5/16″

18 x 1″ hex bolt through a 5/16” flat washer, the slot in th

e long leg of

the closure bracket and the holes in the Vertical Picket closure. Use 5/16” flat

washers and 5/16″

-18 nuts to attach then tighten all fasteners securely (FIG. 5.17).

5.6.6.

Repeat steps 5.6.4 & 5.6.5 on the opposite side when centering the ramp.

Содержание PATHWAY 3G SS06VP











































































Результаты поиска

Содержание PATHWAY 3G SS06VP

Отзывы:

Похожие инструкции для PATHWAY 3G SS06VP

Бренды по названию

Популярные бренды

EZ-ACCESS PATHWAY 3G SS06VP, Инструкция по сборке

Результаты поиска

Содержание PATHWAY 3G SS06VP

Отзывы:

Похожие инструкции для PATHWAY 3G SS06VP

Бренды по названию

Популярные бренды