EZ-ACCESS PATHWAY 3G SS06VP Скачать руководство пользователя страница 63

Страница: 63 / 74

Page 63 of 74

7.4.

LANDING PAD

7.4.1.

The PLP (LANDING PAD) is used at the bottom of a ramp or ramp run to assist

mobility on soft ground. Contour the ground to remove any high or low areas which

would prevent portions of the Landing Pad from contacting the ground.

WARNING The Landing Pad is intended for use on the ground only. The

underside of the Landing Pad must be fully supported by the ground. It should

never be used in an elevated position like a ramp or a platform.

7.4.2.

Slide the bottom plate into one of the three available slots (FIG. 7.5).

The ramp must be installed on the side marked for ramp attachment.

7.4.3.

After installing the bottom plate, install #8-32 hex washer head thread cutting screws

into the screw slots on both sides (FIG. 7.6).

FIG. 7.5

FIG. 7.6

Содержание PATHWAY 3G SS06VP











































































Результаты поиска

Содержание PATHWAY 3G SS06VP

Отзывы:

Похожие инструкции для PATHWAY 3G SS06VP

Бренды по названию

Популярные бренды

EZ-ACCESS PATHWAY 3G SS06VP, Инструкция по сборке

Результаты поиска

Содержание PATHWAY 3G SS06VP

Отзывы:

Похожие инструкции для PATHWAY 3G SS06VP

Бренды по названию

Популярные бренды