background image

ENGLISH

TO FIND OUT WHERE YOUR NEAREST SERVICE CENTRE IS, CONTACT YOUR DEALER OR GO TO THE WEBSITE WWW.LANORDICA-EXTRAFLAME.COM

no flaMe 

The pellet hopper is empty.

No pellet feed.

The gearmotor does not feed pellets.

Check for the presence of pellets in the hopper.

Adjust the pellet flow (see “EASY SETUP”).

DepR alaRM 

The door is not closed correctly.

The ash drawer is not closed correctly.

The combustion chamber is dirty.

The fumes exhaust pipe is blocked/dirty.

Check hermetic door closure.

Check hermetic closure of the ash drawer.

Check cleanliness of the fumes pipe and the combustion chamber.

no 

iGniTion 

The pellet hopper is empty.

Pellet feed calibration inadequate.

Thermostat bulbs tripped

Check for the presence of pellets in the hopper.

Adjust the pellet flow (see “EASY SETUP”).

Check the procedures described in the “Ignition” chapter.

Check the thermostats with bulbs (see chapter on resetting)

no 

iGniTion  

Black ouT

No current during the ignition phase.

Turn the stove OFF using key 1 and repeat the procedure described in the 

"Ignition" chapter.

alaRM

 coMManD auGeR

Abnormal pellet loading. 

Contact after-sales centre

Min H20 pRessuRe 

alaRM      

The system pressure read by the pressure switch 

is too low. 

Possible air in the system; bleed the system. Possible lack of water or leaks 
due to anomalies in some system component.

If the problem persists, contact the after-sales centre 

MaX H20 pRessuRe 

alaRM

Air in the system

Inadequate circulation

Possible air in the system; bleed the system. Lack of adequate circulation. 

Lack of or inadequate safety zone.

The water in the stove has exceeded 95°C. Possible pump defect.

If the problem persists, restore operations must be performed by an 

authorised technician.

H2o pRoBe

H2O probe fault

Contact after-sales centre

* DHW pRoBe

Fault in DHW probe. 

Contact after-sales centre

* BuffeR Tank pRoBe

Fault in Buffer tank probe.

Contact after-sales centre

close

HoppeR - sTove DooR

Pellet hopper open.

Stove door open.

Air inlet clogged or dirty.

Check that the pellet hopper and the combustion chamber door are closed 

correctly.

Check air inlet.

BlockeD pWM alaRM

The pump has stopped permanently.

Pump blocked. Electronic module damaged

Contact after-sales centre

HoT pWM alaRM

The pump is operating but not with good 
performance. Undervoltage 160-194v.
Pump in circuit breaker protection mode.

Contact after-sales centre

sToppeD pWM alaRM

The pump has stopped but is still operational.

Undervoltage < 160v. Overvoltage.

Unexpected external flow.

Contact after-sales centre

sToppeD 2 pWM 

alaRM

The pump has stopped but is still operational.

Problem in a component different to the pump. 

Debris in installation.

Positioning in high temperature.

Contact after-sales centre

floW pWM alaRM

Pump blocked.
Liquid with high density.
Pipe obstructed.

Contact after-sales centre

pWM inTeRface 

alaRM

IPWM output interface damaged, in short 

circuit or not connected

Contact after-sales centre

* if there is an additional system data-sheet.

35

Содержание 001282600









































Отзывы: