background image

INSTALLER: PLEASE LEAVE THIS MANUAL WITH
THE OWNER!!

NOTE:  This  heater  should  not  be  installed  in  a  bedroom  or
bathroom.

SAFETY NOTICE

<

CAUTION: HOT WHILE IN OPERATION. KEEP CHILDREN,
CLOTHING AND FURNITURE AWAY. CONTACT MAY
CAUSE SKIN BURNS.

<

IF THIS HEATER IS NOT PROPERLY INSTALLED,
A HOUSE FIRE MAY RESULT.

<

CONTACT LOCAL BUILDING OFFICIALS ABOUT RE-
STRICTIONS AND INSTALLATION INSPECTION REQUIRE-
MENTS IN YOUR AREA.

<

FAILURE TO COMPLY WITH OWNERS' MANUAL IN-
STRUCTIONS WILL VOID YOUR WARRANTY!

Please read this entire manual before installation. Save these instructions.

EF4001C AutoLite Pellet Stove Insert

Installation & Operating Instructions

PLEASE  READ  THIS  ENTIRE  MANUAL  BEFORE  INSTALLATION
AND  USE  OF  THIS  PELLET  FUEL-BURNING  ROOM  HEATER.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN
PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH.

GENERAL INFORMATION

Installation and repair should be done by a qualified

service person. The heater should be inspected before use
and at least annually by a professional service person. More
frequent cleaning may be required due to fuel quality,
excessive lint from carpeting, bedding material, etc. It is
imperative that control compartments, burn pot and circulat-
ing air passageways of the heater be kept clean.

The EASYFIRE Pellet heater has been designed and
approved for burning 

PREMIUM WOOD PELLETS OF

HIGHEST BTU OUTPUT AND LOWEST % OF ASH
CONTENT ONLY. 

Burning biomass fuels in other forms or

poor quality pellet fuel is not permitted and will void
your warranty and/or could cause a burn back or
house fire. 

FOR BEST RESULTS THE WOOD PELLET

FUEL SHOULD BE ¼” DIAMETER AND
APPROXIMATELY 1”. 

Burning other forms of fuel  is not

permitted and will void all warranties.

This unit has been approved for use with a

 Ø 3" Type L

Pellet Vent System or Stainless Chimney Liner

 (Ø 4" on

runs 10 feet and above).

NEVER use gasoline, gasoline-type lantern fuels,

kerosene, charcoal lighter fluid, or similar liquids to start or
"freshen up" a fire.  Keep all such liquids well away from the
heater while it is in use.

Ashes must be disposed of in a metal container with a

tight fitting lid and placed on a noncombustible floor or
ground, well away from all fuels, pending final disposal.

NOTE :

  During the first few burns the high temperature

paint and sealant used in manufacture will emit some odor
and smoke. Open doors and windows to the outside for
proper ventilation during the first burn cycle and curing of
the paint.

This heater, when installed, must be electrically grounded in
accordance with local codes or, in the absence of local
codes, with the 

National Electrical Code, ANSI/NFPA 70-

2013

.

Provide adequate clearances around air openings into the

combustion chamber and adequate accessibility clearance for
servicing  and  proper  operation.  Never  obstruct  the  front
opening of the heater.

Sierra Products, Inc.
63 Laxalt Dr.
Carson City, NV 89706
(775) 241-2586

Содержание EasyFire EF4001C















Отзывы: