ESPEC BTL-433 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 60

ESPEC BTL-433 Скачать руководство пользователя страница 44

Criterion Series Benchtop User’s Manual

41

Trouble Cause Remedial

Action

Lingering odors inside the cabinet

Clean the test area. See "6.3
Maintenance".

Strange odors are
detected.

Specimens are generated odors.

Remove the source of the odor.

The cabinet is wet on
the outside.

The room is highly humid.

There is nothing wrong with the
equipment. Proceed as planned.

The door is not completely latched.

Shut the door. (See section 5.1.2)

Ambient temperature changes more
than 5°C/hr.

Stabilize ambient temperature and
resume testing.

Temperature
(&humidity) is unstable.

High heat load equipment is being
turned ON/OFF.

Reduce the heat load.

Settings cannot be
changed.

The keys are locked.

Unlock the keys.
See "5.2 User Setup and Safety
Device Options Setup".

The door is not completely latched.

Shut the door. (See section 5.1.2)

Specimen heat load is high.

Reduce the amount of specimens.

Temperature heat-
up/pull-down rate does
not satisfy
specifications.

Ambient temperature too low (high).

Raise (Lower) ambient temperature.

The condense filter is clogged.

Clean the filter (See Section 6.3.)

«
...
42
43
44
45
46
...
»

Содержание BTL-433





























































Отзывы:

Нет отзывов