background image

Criterion Series Benchtop User’s Manual 

 

 

1

Introduction 

 
This manual has been written for users of the Criterion Series Chambers and particularly for technicians.  
Read it thoroughly to obtain the maximum performance from the chamber. 
 

Safety Symbols 

 
The following safety symbols are used throughout this manual. 
 

Degrees of Danger 

 

 

!

VERY
DANGEROUS 

 

This mark means extremely dangerous 
consequences may arise, with the possibility of 
death or serious injury to the user, if the 
equipment is handled incorrectly. 

 

!

DANGER

 

This mark means dangerous consequences 
may arise, with the possibility of death or 
serious injury to the user, if the equipment is 
handled incorrectly. 

 
 

!

CAUTION

 

This mark means dangerous consequences 
may arise, with the possibility of somewhat 
serious injury to the user and/or damage to 
equipment and facilities, if the equipment is 
handled incorrectly. 

 

Key Words 

 
The following keywords are used in this manual. 
 

Note 

Provides information necessary for gaining full performance from the 
chamber or to prevent damage to equipment 

Procedure 

Explains how to operate the chamber on a step-by-step basis. 

Reference : 

Offers 

supplementary 

information. 

 
 

Содержание BTL-433





























































Отзывы:

Похожие инструкции для BTL-433