manualshive.com logo in svg

Ericsson EDACS PRISM HP, Руководство оператора

Поделиться
Скачать
Ericsson EDACS PRISM HP Скачать руководство пользователя страница 89

OPERATING TIPS

The following conditions tend to reduce the effective

range of two-way radios and should be avoided when-
ever possible.

••

Operating the radio in low areas of terrain or while
under power lines or bridges.

••

Operating the radio inside of a vehicle or in a metal
or steel framed building unless using an outside
antenna.

••

Obstructions such as mountains or buildings be-
tween the sending and receiving parties.

In areas where transmission or reception is poor,

some improvements may be obtained by insuring that
the antenna is vertical. Moving a few yards in another
direction or moving to a higher elevation may also im-
prove communication.

BATTERY PACKS

CHARGING THE BATTERY PACK

After receiving a new rechargeable battery pack, it

should be fully charged before placing it into service. This
also applies to rechargeable batteries that have been
stored for long periods. When the battery pack requires
charging, the radio will signal the operator with an alert

tone and the radio will display 

 in its LCD.

89

Содержание EDACS PRISM HP













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды