manualshive.com logo in svg

Ericsson EDACS PRISM HP, Руководство оператора

Поделиться
Скачать
Ericsson EDACS PRISM HP Скачать руководство пользователя страница 44

Deleting Groups From A Scan List

1.

With scan operation turned off, select the desired
group to delete from the selected trunked system’s
group scan list.

2.

Press 

9

. The current status of the group is dis-

played for a time-out period.

3.

While the status is displayed, press 

9

 to delete

the group from the scan list. "S", "2" or "1" turns off.
Any group that is not in a trunked system group scan
list will show a "blank" for the time out period when
it is the selected channel.

Nuisance Delete

A group can also be deleted from the scan list, if it is

not the currently selected group, by pressing 

9

 key

during scan operation while the radio is displaying the
unwanted group. The group will be deleted from the
system’s group scan list in the same manner as if done
using the steps above. Deletions done in this manner will
not remain deleted if the radio is turned off and then back
on.

SCANNING TRUNKED SYSTEMS

Wide Area System Scanning

The PRISM HP radio may be programmed for wide

area system scan operation for roaming across mobile
systems. Upon the loss of the currently selected sys-
tem’s control channel, radios may be programmed to
44

Содержание EDACS PRISM HP













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды