Ericsson EDACS PRISM HP Скачать руководство пользователя страница 36

Страница: 36 / 108

Sending A Group Call

Turn on the radio and set the POWER ON-OFF/VOL-
UME knob to the desired volume level. Select the
desired system and group.

Press and hold the PTT button. The radio will display

the system and group names and perform the

necessary signalling required to obtain a communi-
cation channel.

When the working channel is assigned,

and

are displayed and a short mid-pitch tone sounds

(if programmed) indicating communication can be-
gin.

Hold the radio approximately three inches from the
mouth and speak in a normal voice into the micro-
phone (located upper-left of speaker grille).

Release the PTT button when the transmission is
complete and listen for a reply.

If two or more tones, or a high pitched tone is heard,
the system may be busy and the call request has
been placed in queue or the request has been denied
for some reason. Refer to the ALERT TONES section
for more details.

NOTE

Содержание EDACS PRISM HP













































































































Результаты поиска

Содержание EDACS PRISM HP

Отзывы:

Бренды по названию

Популярные бренды

Ericsson EDACS PRISM HP, Руководство оператора

Результаты поиска

Содержание EDACS PRISM HP

Отзывы:

Бренды по названию

Популярные бренды