manualshive.com logo in svg

Ericsson EDACS PRISM HP, Руководство оператора

Поделиться
Скачать
Ericsson EDACS PRISM HP Скачать руководство пользователя страница 2

NOTICE!

This manual covers Ericsson and General Electric

products manufactured and sold by Ericsson Inc.

NOTE!

Repairs to this equipment should be made only by an
authorized service technician or facility designated by
the supplier.  Any repairs, alterations or substitution of
recommended parts made by the user to this equipment
not approved by the manufacturer could void the user’s
authority to operate the equipment in addition to the
manufacturer’s warranty.

This manual is published by Ericsson Inc., without any warranty. Improvements and changes
to this manual necessitated by typographical errors, inaccuracies of current information, or
improvements to programs and/or equipment, may be made by Ericsson Inc., at any time and
without notice. Such changes will be incorporated into new editions of this manual. No part of
this manual may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose, without the express written
permission of Ericsson Inc.

The software contained in this device is
copyrighted by Ericsson Inc.  Unpublished rights
are reserved under the copyright laws of the
United States.

NOTE

Copyright © July 1995, Ericsson Inc.

2

Содержание EDACS PRISM HP













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды