Ericsson EDACS PRISM HP Скачать руководство пользователя

Страница: 23 / 108

or an individual call is be-
ing attempted to a radio
that is currently transmit-
ting.

DENIED

Call Denied

- Trunked mode only. Indi-

cates the radio is not
authorized to operate on
the selected system.

CC SCAN

Control
Channel
Scan

- Trunked mode only. Indi-

cates the control channel
is lost and the radio has
entered the Control Chan-
nel Scan mode to search
for the control channel.

WA SCAN

Wide Area
Scan

- Trunked mode only. Indi-

cates the control channel
is lost and radio has en-
tered the Wide Area Scan
mode to search for a new
system (if enabled
through programming).

TALKARND

Talk-around

- Conventional mode only.

Indicates the radio is oper-
ating on conventional
channels in talk-around
mode (no repeater).

LOW BATT

Low Battery

- Battery

voltage

has

dropped below the point to
where the radio is no
longer able to transmit.
The radio will still be able

Содержание EDACS PRISM HP













































































































Результаты поиска

Содержание EDACS PRISM HP

Отзывы:

Похожие инструкции для EDACS PRISM HP

Бренды по названию

Популярные бренды

Ericsson EDACS PRISM HP, Руководство оператора

Результаты поиска

Содержание EDACS PRISM HP

Отзывы:

Похожие инструкции для EDACS PRISM HP

Бренды по названию

Популярные бренды