manualshive.com logo in svg

Ericsson EDACS PRISM HP, Руководство оператора

Поделиться
Скачать
Ericsson EDACS PRISM HP Скачать руководство пользователя страница 72

transmitted clear if the digital mode is disabled or inop-
erative.

1.

If receiving an analog message trunked call, the
radio responds in the analog mode during the hang
time on the working channel.

2.

If receiving an analog I-Call, the radio responds in
the analog mode during the hang time.

3.

When using the 

 feature to respond to an

I-Call (after the hang time has expired), the call is
transmitted in the mode defined by the system mode
as programmed for the current system if the ID being
called is not in the I-Call list. If the ID is in the I-Call
list, then the call is transmitted as defined by the
I-Call mode programmed in the list for that ID.

DTMF

The overdial DTMF tones are not available while in

the Aegis Digital Mode.

Mode 3: Aegis Private Modes

The Aegis private modes allow the radio to transmit

encrypted messages and receive clear or private trans-
missions. The radio transmits private if the group/chan-
nel is programmed for private operation and forced op-
eration is pre-programmed. If autoselect operation is
pre-programmed and the radio is in the private mode, the
radio transmits in the mode of the received call if the hang
time is active. If no hang time is active, the radio transmits
private.

*WHC*

72

Содержание EDACS PRISM HP













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды