Environnement Envea MIR 9000 Скачать руководство пользователя страница 114

Страница: 114 / 212

Environnement

S.A

MIR 9000

Duplication prohibited

4–14

JULY 2009

MAINTENANCE SHEET

Serial no. MONITOR:

OPERATION SHEET 4.3.8

Subject: Replacing the optical forks

PAGE: 1/1

Frequency: Depending on need

Date

−

Disassembling the optical bench

(Figure 6.3)

•

Switch off the analyzer.

•

Remove the cap from the optical compartment.

•

Disconnect the connectors J3-J7-J8-J9-J12-J13-J14-J16-J17-J20.

•

Loosen the 2 knurled fastening screws and remove the clamp.

•

Free the measurement chamber from the optical compartment and disconnect the 2

Isoversinic tubes. Carefully mark their respective positions.

/ H

O MIR version

•

Switch off the analyzer.

•

The chopper optical fork can be reached directly from the IR source block.

−

Replacing the optical fork assembly

•

Loosen the 4 screws (4) to remove the source block unit.

•

Loosen the screws (2).

•

Remove the optical forks assembly.

−

Adjusting the synchronisation

•

See chapter 5 paragraph “Adjustment and inspection of the motherboard”.

−

Required tools:

•

∅

4 flat screwdriver.

Содержание Envea MIR 9000





















































































































































































































Результаты поиска

Содержание Envea MIR 9000

Отзывы:

Environnement Envea MIR 9000, Техническое руководство, Страница: 114 / 212

Результаты поиска

Содержание Envea MIR 9000

Отзывы: