Enerpac Turbo II 3000 Series, Инструкция

Страница: 2 / 44

2
WARNING: Only use hydraulic cylinders in a coupled
system. Never use a cylinder with unconnected
couplers. If the cylinder becomes extremely
overloaded, components can fail catastrophically causing
severe personal injury.
IMPORTANT: Hydraulic equipment must only be
serviced by a qualified hydraulic technician. For repair
service, contact the Authorized ENERPAC Service
Center in your area. To protect your warranty, use only
ENERPAC oil.
WARNING: Immediately replace worn or damaged
parts by genuine ENERPAC parts. Standard grade
parts will break causing personal injury and property
damage. ENERPAC parts are designed to fit properly and
withstand high loads.
3.0 DESCRIPTION
TURBO II air pumps are designed to power all standard fixture
workholding systems, operating both single- and double-acting
cylinders effectively.
Because of its ability to recycle its own exhaust air to improve its
efficiency, the 5,000 series TURBO II air pump is recommended for
production automation systems where input air pressure is limited.
The 3,000 Series TURBO II models are preferred for larger
hydraulic circuits requiring higher flow rates.
4.0 INSTALLATION
4.1 Air Supply
Required input operating air pressure range is 25 to 125 psi.
3000 Series
Hydraulic air ratio 50:1 (5000 psi hydraulic pressure at 120 psi air
pressure)
5000 Series
Hydraulic air ratio 72:1 (5000 psi hydraulic pressure at only 80 psi
air pressure)
An Enerpac regulator/filter/lubricator should be installed upstream
from the pump to provide clean, lubricated air and to allow for air
pressure adjustment.
4.2 Air Connection
See Figure 1A. Attach air supply to 1/4 NPT swivel connection on
the end of the pump. Use Teflon tape or similar thread sealant.
Torque to 20-25 ft.-lbs [27-34 Nm].
PARG Models: See Illustrations 1B and 1C. Attach air supply to
either 1/4 NPT connections on top rear to handle or 1/4 NPT
connection on bottom of air pendant. Make sure the unused port is
plugged.
4.3 Hydraulic Connections
WARNING: All hoses and components used with
these pumps must have a working pressure rating
higher than, or equal to, the maximum pressure rating
of the pump.
Model Hydraulic Weight Model Hydraulic Weight
No. Output Ports Number Output Ports
PATG3102NB .375-18 NPTF 19 lbs. (8.6 kg.) PATG5102N .375-18 NPTF 19 lbs. (8.6 kg.)
PATG3105NB .375-18 NPTF 23 lbs. (10.4 kg.) PATG5105NB .375-18 NPTF 23 lbs. (10.4 kg)
PATG3102PB .250-19 BSPP 19 lbs. (8.6 kg.) PATG5102PB .250-19 BSPP 19 lbs. (8.6 kg.)
PAMG3402N .375-18 NPTF 25 lbs. (11.4 kg.) PAMG5402N .375-18 NPTF 25 lbs. (11.4 kg.)
PAMG3402PB .250-19 BSPP 25 lbs. (11.4 kg.) PAMG5402PB .250-19 BSPP 25 lbs. (11.4 kg.)
PACG3002SB #4 SAE 19 lbs. (8.6 kg.) PACG5002SB #4 SAE 19 lbs. (8.6 kg.)
PACG3002PB .250-19 BSPP 19 lbs. (8.6 kg.) PACG5002PB .250-19 BSPP 19 lbs. (8.6 kg.)
PASG3002SB #4 SAE 19 lbs. (8.6 kg.) PASG5002SB #4 SAE 19 lbs. (8.6 kg.)
PASG3002PB .250-19 BSPP 19 lbs. (8.6 kg.) PASG5002PB .250-19 BSPP 19 lbs. (8.6 kg.)
Series Hydraulic Oil Flow Oil Flow Oil Flow Air Pressure Air Consumption Operating Noise
Air Ratio @ 100 psi @ 3,000 psi @ 5,000 psi Range @ 100 psi Level (dBA)
(6.9 bar) (207 bar) (350 bar) (6.9 bar)
3000 50:1 170 cu.in/min. 50 cu.in/min. 0 cu.in/min. 25-125 psi 12 SCFM 76
(2.79 liters/min.) (0.82 liters/min.) (0.0 liters/min.) (1,7-8,6 bar) (0.34 cu.m/min)
5000 72:1 120 cu.in/min. 45 cu.in/min. 20 cu.in/min. 25-125 psi 12 SCFM 76
(1.97 liters/min.) (0.74 liters/min.) (0.33 liters/min.) ( 1,7-8,6 bar) (0.34 cu.m/min)
Reservoir Reservoir Usable Oil Usable Oil
Size Capacity Horizontal Mount Vertical Mount
2 150 cu.in (2.5 liters) 127 cu.in (2.1 liters) 70 cu.in (1.2 liters)
5 255 cu.in (4.2 liters) 230 cu.in (3.8 liters) 180 cu.in (3.0 liters)
SPECIFICATION TABLES