Endress+Hauser Micropilot M FMR250 Скачать руководство пользователя страница 24

Страница: 24 / 120

Installation

Micropilot M FMR250 FOUNDATION Fieldbus

Hauser

FMR250 with top target positioner

Using top target positioner it is possible to tilt the antenna axis by up to 15° in all directions. The
top target positioner is used for the optimum alignment of the radar beam with the bulk solids
surface.

a0011472

Align antenna axis:

Loosen screws.

Align antenna axis (here this is possible up to max. ±15° in all directions).

Tighten screws.

Integrated air purge connection

15°

In extremely dusty applications, the integrated
air purge connection can prevent clogging of the
antenna. Pulsed operation is recommended.

• Pulsed operation:

max. pressure of purge air: 6 bar abs (87 psi).

• Permanent operation:

recommended pressure range of the purge air:
200 mbar to 500 mbar (3 psi to 7.25 psi).

Caution!

Make sure to use dry purge air.

L00-FMR250xx-17-00-00-en-010

air

connection:

(

tor

(

))

Содержание Micropilot M FMR250

























































































































Результаты поиска

Содержание Micropilot M FMR250

Отзывы:

Похожие инструкции для Micropilot M FMR250

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot M FMR250, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot M FMR250

Отзывы:

Похожие инструкции для Micropilot M FMR250

Бренды по названию

Популярные бренды