Elster A1120 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 157

background image

Operating & Maintenance Instructions

37

26 INSTALLATION

26.1 Unpacking

Remove the meter from its packaging and inspect for damage.

Check that there is no movement or loose parts within the meter enclosure.

If damage has been sustained in transit, an immediate claim should be made to the Transport
Company, and a report sent to the Elster Metering Systems branch office or agent.

WARNING

Removal of the main cover seals will invalidate certification.

The meter type and rating must be correct for the intended application.

26.2 Handling

Once removed from the packaging, meters must be treated with care and not subjected to
excessive shock or mechanical vibration.

Care should be taken to avoid marking or scratching the meter case and polycarbonate cover.

26.3

Storage

If the meter is not required for immediate use, it should be returned to the original packing
(including plastic bag) and stored in a clean, dry environment.
Storage temperature:

-25

°

C to +85

°

C

26.4

Installation Site

The installation site should be a dry indoor environment and, as far as is practicable, away from
direct sunlight and free from mechanical shock and vibration.

26.5

Electromagnetic Compatibility (EMC)

The A1120/40 meter has been designed and tested for compliance with the EMC Directive.

It is, however, the responsibility of the installer for ensuring that a system conforms to the
Directive.

«
...
43
44
45
46
47
...
»

Содержание A1120






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для A1120

Charge Analyzer 711

Бренд: 3M Страницы: 24

Acuvim-L Series

Бренд: AccuEnergy Страницы: 83

Бренд: Bamo Страницы: 8

Бренд: Van Walt Страницы: 12

Clavinova CLP-311

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 3

Alto Horn, Baritone, Euphonium

Бренд: Yamaha Страницы: 22

Clavinova CLP-320

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 20

Бренд: YOKOGAWA Страницы: 2

ADMAG TI Series

Бренд: YOKOGAWA Страницы: 8

Бренд: Avery Weigh-Tronix Страницы: 54

IMI Sensors Spindler 607A61

Бренд: PCB Piezotronics Страницы: 24

Бренд: ACL Staticide Страницы: 5

Бренд: Hanna Instruments Страницы: 28

WTW SensoLyt 900

Бренд: Xylem Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды