Elster A1120 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 157

background image

Power Master Unit

11

___________________________________________________________________________

Scheme Editor

3.1

Selecting the Meter Type

Before using the Scheme editor, the type of meter to
be programmed must be selected.
Select File/New/A1120/40 Scheme and open the
scheme. Select Compatibility on the Main Menu Bar.

Select the appropriate meter variant only. From now
on the Power Master Unit will only display parameters
applicable to the selected model(s) of A1120/40
Meter. It is strongly recommended that only one meter
variant is selected at a time. If more than one variant
is selected and a Scheme is created, scheme
parameters applicable to the lowest specification of
meter only will be available for selection.

To Select meter compatibility -

Select compatibility

A1120 in the Scheme Editor

then

select meter variant.

If 'Save as Default' is checked, the selection will be saved and used as the default when the Power
Master Unit is powered up and new schemes are created.

3.2

Scheme Editor

As an entry is made to a Scheme

,

the entry in the Summary changes to

Bold

(See opposite). This allows quick verification of Scheme

entries.

Care should be taken when entering a Scheme to ensure the correct parameters
are selected for generic meter models. If a parameter is not available for a
particular model of meter, the meters will still be programmed, but no action will
take place for the unavailable parameter. For this reason it is recommended that
meter compatibility is selected in isolation.

«
...
108
109
110
111
112
...
»

Содержание A1120






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для A1120

TUNICS T100S-HP

Бренд: Yenista Optics Страницы: 66

Charge Analyzer 711

Бренд: 3M Страницы: 24

Бренд: Bamo Страницы: 8

Бренд: DAKOTA ULTRASONICS Страницы: 25

Бренд: DAKOTA ULTRASONICS Страницы: 36

POCKET COLORIMETER II

Бренд: Hach Страницы: 188

Stage Piano MP8

Бренд: Kawai Страницы: 70

Бренд: Olympus Страницы: 362

Бренд: Olympus Страницы: 8

Бренд: UEi Страницы: 5

Бренд: Apogee Страницы: 22

Smart Air Quality Monitor

Бренд: Lennox Страницы: 28

Бренд: Roland Страницы: 96

Бренд: Xylem Страницы: 10

Бренд: Lasertec Страницы: 32

Бренд: IDEAL Страницы: 20

Trimble Ranger 3

Бренд: Badger Meter Страницы: 20

Бренд: A&D Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды