Elster A1120 Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 157

background image

16

A1120/1140 Programmable Polyphase Meter Users Manual

___________________________________________________________________

Season Changeover Dates

24 Season Changeover Dates

Season Changeover Dates are the dates on which
a new season begins. Season Change Over Dates
are defined by day, month and season number.

Entering the seasons changeover dates

To enter a fixed date -

Select the first season then

click on the Season Dates column at the start of the
required Season.

Click and drag to the Season end date

Repeat for all Seasons

Select Scheme/Save page

If a date other than the first day of the month is required for the season start date, click on the ‘day’ tab
and use the scroll bar to find the start of the season. Click and drag to the Season end date

To enter a variable date -

Check Enable Advanced Season

Editing then select the Season.

From the Season Change Editor, select Last Monday in April.

Selecting Next starts on Last Sunday in September.

Select OK.

Note:

February 29 will only be activated on leap years even

if selected, otherwise the February 28 will be used.

The calendar can be viewed by day or by month by selecting the
appropriate option at the bottom of the calendar.

Billing Reset

A Billing Reset can be activated by selecting ‘perform a billing reset on change season’.

Exclusion Dates

32 Exclusion Dates

Exclusion Dates are the dates when the normal switching times for that season are not to be adopted
i.e. Public Holidays. Instead, Switching times with defined actions take over.

A switching time for the 1 Jan is shown opposite.
The shaded box indicates the season or day to switch to i.e. Holiday
is the day type selected to use.

©

Elster Metering Ltd - M181 001 3C - 12/2007

«
...
113
114
115
116
117
...
»

Содержание A1120






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для A1120

Бренд: BANTE inststruments Страницы: 15

Бренд: 3Bays Страницы: 21

Бренд: Kane Страницы: 19

Бренд: Weller Страницы: 9

Бренд: Sanmenxia Страницы: 17

Бренд: SANKO Страницы: 25

Бренд: Samson Страницы: 2

Professional Plus

Бренд: YSI Страницы: 28

Бренд: Bontempi Страницы: 18

Бренд: Sper scientific Страницы: 12

Scuba MAXIMUS SRB3600 regulator

Бренд: Sherwood Scuba Страницы: 29

Бренд: Lumel Страницы: 40

Micro Alti Vario Plus

Бренд: Fairhaven Страницы: 20

Бренд: BC Biomedical Страницы: 9

MLS 50-3...N series

Бренд: KERN Страницы: 16

Бренд: Hanna Instruments Страницы: 2

MASTERVISION ECO

Бренд: Ega Master Страницы: 48

Бренд: AquaMetrix Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды