Elster A1120 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 157

background image

Power Master Unit

1

_________________________________________________________________

Power Master Unit

1.1

Power Master Unit Introduction

This section gives the basics on how to use the Power Master Unit software.

The Power Master Unit (Referred to in this manual as the Master Unit) software is a menu driven
package designed to support all variants of Elster Metering Systems:

A1700 (PPM) Polyphase Commercial and Industrial Meters

A1120/40 Light Industrial and Commercial Meters

A120/140 Electronic Single-phase Domestic Meters

Power Master Unit meter compatibility does not allow different meter types to be programmed by the
same scheme, therefore a separate manual support's each application. This manual supports A1120
and A1140 meters only. For information on how to program the A1700 and PPM meters, see manual
M120 001 6.

To program A120/140 meters, see manual M130 001 3.

The key features of the Master Unit software are:

Menu driven, using Microsoft

®

Windows based operating software to guide the user through the

process of setting up a meter for any particular application.

Programming structure to ensure that, if an attempt is made to program a feature that is not present in
a meter, erroneous data cannot be programmed.

All other features are programmed normally.

The Software permits:

Reading and Programming directly through the optical port

Reading and Programming through the serial port either directly or via a modem

Reading and Programming indirectly via a Hand Held Unit (HHU) through the optical port

Transferring information to and from a HHU

1.2 Prerequisites

This tutorial assumes you are comfortable with the 'Microsoft Windows' environment.

The Master Unit is Windows

™

compatible, but if you are uncertain of the Windows structure, it is worth

spending a little time familiarising yourself with the 'Brief Tour of Microsoft Windows' in the Windows
manual before entering the software.

«
...
98
99
100
101
102
...
»

Содержание A1120






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для A1120

Бренд: Kawai Страницы: 2

Бренд: DAE Страницы: 28

Бренд: Oakton Страницы: 4

Бренд: OHAUS Страницы: 2

Бренд: janitza Страницы: 48

Бренд: ColorLite Страницы: 68

Бренд: Facom Страницы: 48

Бренд: Hanna Instruments Страницы: 2

Бренд: Ratek Страницы: 25

Бренд: Omega Страницы: 4

Бренд: Alpes Lasers Страницы: 41

Бренд: Thermo Scientific Страницы: 56

Бренд: Velleman Страницы: 15

Бренд: Camlab Страницы: 28

Commissioner dali

Бренд: Artistic License Страницы: 26

Бренд: Dadam micro Страницы: 24

Бренд: promesstec Страницы: 72

Бренд: Universal Laser Systems Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды