Elster A1120 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 157

background image

56

A1120/40 - Electronic Polyphase Meter

©

Elster Metering Limited - M181 001 2G - 5/2010

APPENDIX A - Checking kWh and kvarh Registration Accuracy

WARNING

Only trained and competent personnel, familiar with meter test procedures should carry out the
following operation.

A1 Introduction

Various methods of checking the accuracy of registration of the A1120/40 meter are available.
Methods using the LED test indicators and Register advances are described below.

A2

Checking Meter Accuracy Using the LED Test Indicator

The LED test indicators are configured at manufacture to pulse for import kWh and import kvarh
(import only meter) or pulse for import plus export kWh and kvarh (import/export or power flow
insensitive meters).

A2.1

Comparing the number of LED pulses with substandard meter register advance

What you will need

Suitable test equipment with a sensor to detect LED pulses

A suitable substandard meter (set to the same system configuration as the meter under test)

A counter for counting the number of LED pulses

Checking registration

In order to achieve a repeatability of 0.1% the test time at any load needs to be a minimum of 60
seconds.

1. Connect the test equipment and a suitable load to the meter, then power up the meter

2. The right hand Test LED pulses for kWh

3. Run the test for a suitable duration and check the amount the substandard has advanced and

the number of pulses detected

Calculate the registration by dividing the number of pulses by the meter constant.

e.g. 994 (LED count) = 0.994 kWh advance.
1000 (meter constant)

Compare this kWh advance with the amount the substandard has advanced.

Repeat for kvarh using left hand Test LED.

«
...
62
63
64
65
66
...
»

Содержание A1120






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для A1120

Workstation Monitor 724

Бренд: 3M Страницы: 21

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 24

Бренд: 3M Страницы: 2

SoundPro SE Series

Бренд: 3M Страницы: 293

Бренд: Kane Страницы: 16

Бренд: Kane Страницы: 60

Бренд: Garmin Страницы: 120

Бренд: OHAUS Страницы: 84

Бренд: Halcyon Страницы: 36

Бренд: Omano Страницы: 14

Бренд: Midcontinent Страницы: 6

Бренд: Omega Страницы: 31

Dakota Ultrasonics ZX-2

Бренд: ABQ Industrial Страницы: 27

Бренд: POSEIDON Страницы: 13

Бренд: Polimaster Страницы: 24

Бренд: NARDA Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды