Elster A1120 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 157

background image

Operating & Maintenance Instructions

31

19

BATTERY BACK-UP

The A1120/40 has an internal battery that supports the clock and calendar.

An optional external battery that supports the reading of meter data and display facilities during
power outages can be provided.

19.1 Internal

Battery

In the event of an a.c. failure, an internal battery (a Lithium ‘coin’ cell) supports the real time
clock.

The battery is soldered onto the printed circuit board.

The meter can be programmed to initiate one of the following courses of action should the supply
fail and the battery become exhausted. When the supply returns: -
a.

Freeze the TOU registers and increment the total cumulative registers only

b.

Assume the last known time and continue to use the TOU registers

See Section 29 for battery disposal.

19.1.1 Internal Battery Monitoring

The battery provides support for the life of the meter. The following functions are provided on the
Battery Monitor: -

Elapsed Time -

The total amount of battery support time is monitored. The elapsed time counter

decrements to represent the use/shelf life of the battery.

Remaining Time -

The remaining battery life is calculated by subtracting the elapsed time from

the expected time. The remaining life may be read via the optical or RS232 communications port
and its value optionally included in the display sequence.

If the remaining time falls to zero, a ‘flag’ is set which can be read by via the optical port or RS232
port.

Failed Battery -

The occurrence of total battery fail is monitored each time the meter is

energised. A flag is set and the time and date recorded when the meter last powered down.

«
...
37
38
39
40
41
...
»

Содержание A1120






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для A1120

Бренд: ABB Страницы: 8

Бренд: DayTronic Страницы: 54

Бренд: Bacharach Страницы: 2

Бренд: Bachmann Страницы: 33

Бренд: Omano Страницы: 14

Бренд: Ulvac Страницы: 18

Бренд: X-Rite Страницы: 45

Бренд: X-Rite Страницы: 22

Бренд: Rabid Elephant Страницы: 18

Бренд: ILX Lightwave Страницы: 126

STORA-ABG RKS-01

Бренд: ECOTEST Страницы: 146

Бренд: Johnson & Associates Страницы: 33

Бренд: PCE Health and Fitness Страницы: 11

SensoControl Serviceman SCM-150 Series

Бренд: Parker Страницы: 39

Бренд: RADWAG Страницы: 176

Бренд: Solinst Страницы: 2

Бренд: PASCO Страницы: 4

DELMHORST J-2000

Бренд: ABQ Industrial Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды