Elster A1120 Скачать руководство пользователя страница 117

Страница: 117 / 157

A1120/1140 Programmable Polyphase Meter Users Manual

___________________________________________________________________

To transfer a group of sequential displays -

Click on the first display in the list.

Hold down the shift key.

Click the last display required in the list (the displays will appear highlighted) then drag the highlighted
displays to the display list.

Using the Buttons

To Transfer a display -

Select the required display from the Available display list.

Click the

button. The display is transferred from the Available display list to the Display list.

To Remove a display from the display list -

Click on the required display

Click the

button. The display is removed.

To Change the display order -

Click on the required display and click the

button to move the

display upwards in the display order.

Click on the required display and click the

button to move the display downwards in the display

order.

Utility Display

Up to 40 Displays can be shown in the A1120/40 Utility display sequence.

The displays are entered in exactly the same way as the Consumer Display.

Checksum

This includes a checksum of the complete Tariff/Display Scheme. The checksum can be used to verify
the meter is running the same scheme as in the PMU.

3.4.5

Deferred Tariff/Display

The deferred Tariff/Display is a pre-defined tariff that will become active specified by the user in the
Deferred Tariff Setup.

The setup for the deferred Tariff/Display is exactly the same as Tariff/Display.

Elster Metering Ltd - M181 001 3C - 12/2007

Содержание A1120






























































































































































Результаты поиска

Содержание A1120

Отзывы:

Похожие инструкции для A1120

Бренды по названию

Популярные бренды

Elster A1120, Руководство пользователя

Результаты поиска

Содержание A1120

Отзывы:

Похожие инструкции для A1120

Бренды по названию

Популярные бренды