elsner elektronik Salva KNX basic Скачать руководство пользователя страница 51

Страница: 51 / 74

Temperature and humidity parameters

Smoke alarm Salva KNX

• Version: 09.09.2016 • Technical Changes and Errors excepted.

Set the

hysteresis

independent of the type of threshold value specification.

Switching output

Set the behaviour of the switching output when a threshold value is exceeded/under-
cut. The output switching delay can be set using objects or directly as a parameter.

Block

The switching output can be blocked using an object.

If the block is activated, define specifications here for the behaviour of the output when
blocked.

Hysteresis setting

in % • absolute

Hysteresis in 0.1°

0...1100; 50

Hysteresis in % of the threshold value

0 … 50; 20

When the following conditions apply,
the output is
(TV = Threshold value)

• TV above = 1 | TV - hyst. below = 0
• TV above = 0 | TV - hyst. below = 1
• TV below = 1 |TV + hyst. above = 0
• TV below = 0 |TV + hyst. above = 1

Delays can be set via objects
(in seconds)

No • Yes

Switching delay from 0 to 1

(If delay can be set via objects:
valid until 1st communication)

None • 1 s • 2 s • 5 s • 10 s • … • 2 h

Switching delay from 1 to 0

(If delay can be set via objects:
valid until 1st communication)

None • 1 s • 2 s • 5 s • 10 s • … • 2 h

Switching output sends

• on change
• on change to 1
• on change to 0
• on change and periodically
• on change to 1 and periodically
• on change to 0 and periodically

Cycle

(only if sending periodically is selected)

5 s • 10 s • 30 s… • 2 h

Use switching output block

No • Yes

Analysis of the blocking object

• At value 1: block | At value 0: release
• At value 0: block | At value 1: release

Blocking object value before
1st communication

0 • 1

Behaviour of the switching output

On block

• Do not send message
• send 0
• send 1

Содержание Salva KNX basic











































































Результаты поиска

Содержание Salva KNX basic

Отзывы:

Похожие инструкции для Salva KNX basic

Бренды по названию

Популярные бренды

elsner elektronik Salva KNX basic, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Salva KNX basic

Отзывы:

Похожие инструкции для Salva KNX basic

Бренды по названию

Популярные бренды