elsner elektronik Salva KNX basic Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 74

background image

12

Installation and commissioning

Smoke alarm Salva KNX

• Version: 09.09.2016 • Technical Changes and Errors excepted.

2.4. Installing the device

2.4.1. Instructions for assembly and initial start-up

Never expose the device to water (e.g. rain) or dust (e.g. drilling dust). This can damage
the electronics and the sensor system. A relative air humidity of 93% may not be ex-
ceeded. Avoid condensation.

After the bus voltage has been applied, the device will enter an initialisation phase last-
ing a few seconds. During this phase no information can be received or sent via the
bus.

2.4.2. Assembly preparation and skirting assembly

Determine the installation point on the room ceiling. Please observe the instructions in
chapter

Installation location

, page 8 for this.

BEWARE!
Injury hazard in case of improper fastening!

The device may fall and injure people if it is not fastened properly.
•

Observe, the carrying capacity of the wall/ceiling material when
selecting the place of installation.

•

Use fixing materials that are suitable for the material underneath.

If you are using the screws and dowels provided, use a 6mm drill to drill holes with a
distance of 67 mm (if you are using two screws for installation). Use the skirting of the
smoke alarm as a stencil. Insert the dowels into the drilling holes.

As an alternative, the skirting of the alarm may be attached to the ceiling with double-
sided adhesive pad (VdS approved). Carefully check the ceiling surface carefully for
lasting carrying and adhesive capacity before using adhesive pads. If necessary, do a
test glueing application. Optimum adhesive power can only be obtained on a clean sur-
face.

Fig. 5

The housing is removed from the skirting by
turning it anti-clockwise.

Fig. 6

Remove the cover on the opening for the sup-
ply line (1) from the skirting and thread the ca-
ble through it.

Screw the smoke alarm skirting onto the ceil-
ing (2, openings for screws).

2

1

«
...
11
12
13
14
15
...
»

Содержание Salva KNX basic











































































Отзывы:

Нет отзывов

Похожие инструкции для Salva KNX basic

Tynetec Deaf Smoke ZXT487

Бренд: LEGRAND Страницы: 3

Pursuit PRO-9342WOS2

Бренд: Audiovox Страницы: 6

Бренд: Olympia Страницы: 40

Бренд: NATURE & DECOUVERTES Страницы: 17

Бренд: Velleman Страницы: 16

Wake 'n' Shake Voyager

Бренд: Geemarc Страницы: 2

Бренд: iHome Страницы: 12

Бренд: Panther Страницы: 14

Бренд: Panther Страницы: 32

Бренд: Masterbuilt Страницы: 36

Бренд: Masterbuilt Страницы: 36

Бренд: System Sensor Страницы: 4

Бренд: i-box Страницы: 88

Бренд: Clas Ohlson Страницы: 5

Бренд: Silencer Security Systems Страницы: 4

Бренд: Code Alarm Страницы: 5

Бренд: Avital Страницы: 20

Бренд: Code Alarm Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды