elsner elektronik Salva KNX basic Скачать руководство пользователя страница 63

Страница: 63 / 74

Temperature and humidity parameters

Smoke alarm Salva KNX

• Version: 09.09.2016 • Technical Changes and Errors excepted.

If necessary, activate the block for the summer compensation and set what a 1 or 0 at
the block input means and what happens in the event of a block.

8.5.

Humidity Measurement

Select, whether a

malfunction object

is to be sent if the sensor is faulty.

Use

Offsets

to adjust the readings to be sent.

The unit can calculate a

mixed value

from its own reading and an external value. Set

the mixed value calculation if desired. If an external portion is used, all of the following
settings (threshold values, etc.) are related to the overall reading.

The

minimum and maximum readings

can be saved and sent to the bus. Use the

"Reset humidity min/max. value" objects to reset the values to the current readings.
The values are not retained after a reset.

Use block

No • Yes

Analysis of the blocking object

• At value 1: block | At value 0: release
• At value 0: block | At value 1: release

Blocking object value before first call

0 • 1

Action when locking

• do not send
• Send value

Value (in increments of 0.1°C)

(if a value is sent during blocking)

0 ... 500; 200

Use malfunction object

No • Yes

Offset in 0.1°C

-50…50; 0

Use external measured value

No • Yes

Ext. Reading proportion of the total reading

5% • 10% • ... • 50% • ... • 100%

Sending pattern for internal and total mea-
sured value

• never
• periodically
• on change
• on change and periodically

At and above change of

(if sent on change)

0.1% RH • 0.2% RH • 0.5% RH • 1.0% RH • ...
• 20.0% RH

Send cycle

(if sent periodically)

5 s • 10 s • ... • 2 h

Use minimum and maximum value

No • Yes

Содержание Salva KNX basic











































































Результаты поиска

Содержание Salva KNX basic

Отзывы:

Похожие инструкции для Salva KNX basic

Бренды по названию

Популярные бренды

elsner elektronik Salva KNX basic, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Salva KNX basic

Отзывы:

Похожие инструкции для Salva KNX basic

Бренды по названию

Популярные бренды