elsner elektronik Salva KNX basic Скачать руководство пользователя страница 17

Страница: 17 / 74

Maintenance

Smoke alarm Salva KNX

• Version: 09.09.2016 • Technical Changes and Errors excepted.

Check if the LED is flashing and conduct a function test.
>

Function test

, page 15

4.2.1. Types of batteries

WARNING!
Danger of explosion in case of improper handling of the battery!

•

Only replace with a lithium battery type DFK CP-V9Ju.

•

Do not use rechargeable batteries or mains units for voltage supply
to ensure a sufficiently high voltage and supply even in case
of a mains outage.

•

Do not recharge batteries and do not short-circuit them.

•

Do not force batteries open or damage them and do not
bring them into contact with fire, water or high temperatures.

The used battery and the device must be disposed of properly so that
valuable resources may be recycled. Neither the battery nor the device
may be disposed of together with domestic or company waste.

Approved battery type

FDK CP-V9Ju
Only use lithium batteries

Average service life

approx. 10 years (typical),
under normal conditions as per EN 14604

Fig. 12

Connect the new battery to the smoke alarm
(check for correct polarity!) and insert it into
the battery compartment.

Fig. 13

Place the housing with the new battery onto
the skirting and fasten it by turning it clock-
wise.

Содержание Salva KNX basic











































































Результаты поиска

Содержание Salva KNX basic

Отзывы:

Похожие инструкции для Salva KNX basic

Бренды по названию

Популярные бренды

elsner elektronik Salva KNX basic, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Salva KNX basic

Отзывы:

Похожие инструкции для Salva KNX basic

Бренды по названию

Популярные бренды