elsner elektronik Salva KNX basic Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 74

background image

15

Maintenance

Smoke alarm Salva KNX

• Version: 09.09.2016 • Technical Changes and Errors excepted.

4.1. Function test

BEWARE!
Danger of hearing damage!

During the function test (pressing on the light transmission bar),

a loud, shrill tone is sounded (at least 85 dB).
•

Keep a minimum distance of 50 cm between smoke alarm and ear.

1. Conducting a visual inspection:

Check:
•

Is the device found at the expected position?

•

Are the smoke entry openings clean? - Remove dust if necessary. The device
must not be painted over.

•

Is the device free from mechanical damage? - Replace the device if it is
damaged.

2. Conducting a function test:

If the function test is successful, a signal tone sounds. The smoke alarm works proper-
ly. If there is no signal tone, the device is not functioning. In this case, replace the bat-
tery and conduct the function test again. If there is still no signal tone, the device is de-
fect and must be replaced.

Smoke alarms must be replaced with new devices after a maximum
period of 10 years according to DIN 14604.

4.2. Replace the battery

The device is supplied with 9 V voltage from a battery. Lack of battery capacity is sig-
nalled optically and acoustically for 30 days and transmitted to the bus.

Fig. 10

Press the light transmission bar for at least 1
second.

Fig. 11

Separate the smoke alarm from the skirting
by turning it anti-clockwise.

«
...
14
15
16
17
18
...
»

Содержание Salva KNX basic











































































Отзывы:

Нет отзывов

Похожие инструкции для Salva KNX basic

Бренд: Eaglemaster Страницы: 7

Бренд: Climax Technology Страницы: 3

Uniguard Superflow UG-5-AFR Series

Бренд: CALECTRO Страницы: 4

Cig-Arrête CSA-POD

Бренд: Radal Technology Страницы: 4

Бренд: Prestige Страницы: 16

Бренд: jablotron Страницы: 2

Бренд: RED Страницы: 2

Бренд: RHINO Страницы: 8

Бренд: RHINO Страницы: 26

Бренд: Wisoee Страницы: 2

Бренд: PAX Страницы: 12

Бренд: Char-Broil Страницы: 64

Бренд: Eurochron Страницы: 4

Бренд: System Sensor Страницы: 12

Бренд: HumanTechnik Страницы: 28

Бренд: System Sensor Страницы: 4

Бренд: System Sensor Страницы: 8

Бренд: ADE Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды