elsner elektronik Salva KNX basic Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 74

background image

52

Temperature and humidity parameters

Smoke alarm Salva KNX

• Version: 09.09.2016 • Technical Changes and Errors excepted.

The

mode

may be switched with two 8 bit objects of different priority. Objects

„... HVAC mode (Prio 2)“ for switching in everyday operation and
„... HVAC mode (Prio 1)“ for central switching with higher priority.
The objects are coded as follows:
0 = Auto
1 = Comfort
2 = Standby
3 = Eco
4 = Building Protection

Alternatively, you can use three objects, with one object switching between eco and
standby mode and the two others activating comfort mode and frost/heat protection
mode respectively. The comfort object blocks the eco/standby object, and the frost/
heat protection object has the highest priority. Objects
„... Mode (1: Eco, 0: Standby)“,
„... comfort activation mode" and
„... frost/heat protection activation mode"

Select the

mode to be activated after reset

(e.g. power failure, reset of the line via

the bus) (Default).
Then configure a temperature control

block

via the blocking object.

Specify when the current

control variables

of the controller are to be

sent

to the bus.

Periodic sending is safer, in case a message does not reach a recipient. You may also
set up periodical monitoring by the actuator with this setting.

Switch mode via

• two 8 Bit objects (HVAC Modes)
• three 1 bit objects

Mode after reset

• Comfort
• Standby
• Eco
• Building protection

Behaviour of the blocking object with value

• 1 = Block | 0 = release
• 0 = block | 1 = release

Value of the blocking object after reset

0 • 1

Send control variable

• on change
• on change and periodically

from change (in % absolute)

1...10; 2

Cycle

(if sent periodically)

5 s • ... • 5 min • … • 2 h

«
...
51
52
53
54
55
...
»

Содержание Salva KNX basic











































































Отзывы:

Нет отзывов

Похожие инструкции для Salva KNX basic

Бренд: Hearing Products Страницы: 2

Pursuit PRO-9775T

Бренд: Audiovox Страницы: 12

Longhorn 21202124

Бренд: oklahoma joes Страницы: 36

Meridian WLS906-433

Бренд: DSC Страницы: 2

Бренд: HANNspree Страницы: 38

Z-SMOKE DETECTOR

Бренд: Heatit Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Toyota Страницы: 41

Бренд: iHome290 Страницы: 1

Бренд: Coopers Страницы: 2

Бренд: Black Widow Security Страницы: 4

Xtralis ICAM ILS-1

Бренд: Xtralis Страницы: 24

Бренд: Xtralis Страницы: 50

Бренд: Masterbuilt Страницы: 36

Бренд: Masterbuilt Страницы: 36

Бренд: Code Alarm Страницы: 12

Professional Series CA 1050

Бренд: Code Alarm Страницы: 20

Бренд: Sparkrite Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды