elsner elektronik 10115 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 50

background image

16

After installation, remove the "Distance" notice
sticker on the top of the cover.

Details for the installation of the weather station

Do not open the weather station if water (rain) might ingress: Even some drops might
damage the electronic system.
Observe the correct installation. Wrong installation might destroy the weather station
and the control electronics.

Please take care not to damage the temperature sensor (small circuit board at the
bottom part of the housing.) when mounting the weather station. Please also take care
not to break away or bend the cable connection between the circuit board and the rain
sensor when connecting the weather station.

Installation of operating unit

The operating unit is battery-powered and communicates with the weather station per
radio.
When you select the assembly site, please avoid direct sun because this would distort
the measurements of the indoor temperature. The appropriate sensor is integrated in
the lower part of the operating unit. For the same reason, the operating unit should not
be installed above the heater. Please make also sure that there is no direct air supply
coming from windows or doors which would distort measured values.

The operating unit may be installed and operated in dry
interior rooms only.

«
...
15
16
17
18
19
...
»

Содержание 10115



















































Отзывы:

Нет отзывов

Похожие инструкции для 10115

Бренд: Lattice Semiconductor Страницы: 30

Бренд: Gardena Страницы: 100

Бренд: easydriver Страницы: 26

Бренд: Calsense Страницы: 10

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 95

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 33

Бренд: Danfoss Страницы: 59

Бренд: Danfoss Страницы: 16

VLT AQUA Drive FC 200

Бренд: Danfoss Страницы: 91

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 100

Бренд: Danfoss Страницы: 82

Бренд: Danfoss Страницы: 18

Бренд: Danfoss Страницы: 12

OPTYMA Plus OP-LPQM

Бренд: Danfoss Страницы: 8

ecomat 100 R 360

Бренд: IFM Electronic Страницы: 16

Бренд: IFM Electronic Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды