Electronics Line Commpact, Руководство по установке

Страница: 39 / 160

Hata! Burada görünmesini istedi ğ iniz metne Heading 1 uygulamak için Giri ş sekmesini kullan ı n. Hata! Burada
görünmesini istedi ğ iniz metne Heading 1 uygulamak için Giri ş sekmesini kullan ı n.
CommPact Installation Manual
35
2. Enter the Telecontrol code (Code 29) on your telephone within 15 seconds.
Do not enter your user code until you hear the two DTMF tones. Any digits entered before
the tones are sounded are disregarded by the system.
3. A DTMF tone is sounded to indicate that the system is ready to receive commands.
The following DTMF commands are available:
o
Press ʺ 2 ʺ for Two ‐ Way Audio.
If the TWA mode is defined as ʺ Simplex ʺ (see 70, 10.6.11, TWA Mode.), the audio
channel opens in Listen mode (microphone active/speaker mute). To switch to Speak
mode, press ʺ 1 ʺ on your telephone. To switch back to Listen mode, press ʺ 0 ʺ on your
telephone.
During the TWA session, you can adjust the speaker volume using the arrow buttons.
o
Press ʺ 3 ʺ to fully arm the system.
o
Press ʺ 430 ʺ to activate PGM output (Unit 30)
o
Press ʺ 530 ʺ to deactivate PGM output (Unit 30)
o
Press ʺ 6 ʺ to disarm the system.
o
Press ʺ 9 ʺ to cancel the siren.
Arm/Disarm, PGM on/off, and Siren Canceling can also be executed at any time
during a Two ‐ Way Audio session.
Error beeps (three tones) sound in case of a wrong command.
To clear the last command, press ʺ * ʺ or ʺ # ʺ .
o
The duration of the call is determined by the TC/VM Timeout ‐‐ see p.70, 10.6.10
Telecontrol/Vocal Message Timeout. Ten seconds before the timeout expires, two
short DTMF tones are sounded. To extend the call, press ʺ 7 ʺ on your telephone.
This command restarts the timeout.
4. To disconnect before the end of the timeout, press ʺ * ʺ then ʺ # ʺ on your telephone.
5.1.5. Arm/Disarm DTMF Commands
During a Telecontrol call, you can arm and disarm the system remotely using the DTMF commands
3 ʺ (arm) and ʺ 6 ʺ (disarm). When arming the system in this way, the system is armed immediately
without an exit delay.
5.1.6. PGM DTMF commands
During a Telecontrol call, you can activate and deactivate PGM using the DTMF commands ʺ 430 ʺ
(PGM On) and ʺ 530 ʺ (PGM Off).
5.1.7. Siren Cancel ("Bell Cancel")
The siren is muted during Two ‐ Way Audio communication. At the end of the call, the siren is re ‐
activated (if the Siren Cut ‐ Off has not yet expired). During the call, pressing ʺ 9 ʺ on your telephone
cancels the re ‐ activation of the siren.
5.1.8. Central Station Two-Way Audio
Central Station Two ‐ Way Audio is an alarm verification feature that enables the central station
operator to establish Two ‐ Way Audio communication with the Control System within ten minutes
of an alarm.