Effekta AX M2 Series Скачать руководство пользователя страница 15

Страница: 15 / 132

Innovating power.

AX M2 series 3-5 kW | Solar inverter

Solar inverter | V1.7

Safety

–

Page 15

1.4.5

Safety instructions for maintenance and repairs

▪

High and low voltage: risk of injury!

−

The battery circuit is not disconnected from the input voltage.

Hazardous voltages can occur between the battery poles and

the ground. Confirm that voltage is not present before touching!

−

Before commencing with maintenance or repair work on the device, you

must
disconnect the device from the supply network and the battery feed.

▪

Residual energy: risk of injury!

−

Even after the device has been disconnected from the power

supply, the components of the solar inverter are still energized

(battery feed!) and are dangerous!

−

Before performing maintenance and/or service work, disconnect the

batteries from the power supply and ensure that there is no electricity

and no dangerous voltage on the terminals of high-performance

condensers, such as e.g. BUS condensers!

▪

Improper repair work: risk of injury!

−

Improper repair work can lead to unexpected behavior of the solar

inverter! This can cause injury to persons.

Figure 2: Safety instructions for maintenance and rapairs

Содержание AX M2 Series





































































































































Результаты поиска

Содержание AX M2 Series

Отзывы:

Похожие инструкции для AX M2 Series

Бренды по названию

Популярные бренды

Effekta AX M2 Series, Руководство пользователя

Результаты поиска

Содержание AX M2 Series

Отзывы:

Похожие инструкции для AX M2 Series

Бренды по названию

Популярные бренды