manualshive.com logo in svg

EFD Ultra 325TT, Руководство пользователя, Страница: 7 / 79

Поделиться
Скачать
EFD Ultra 325TT Скачать руководство пользователя страница 7

i.

LOCK-OUT TAG-OUT PROCEDURE

1.

Announce lockout to other personnel.

2.

Verify that all dispensing motion has stopped.

3.

Turn power 

OFF

at main power circuit breaker at the back of the Ultra TT

4.

Disconnect the power cord from the electrical source. Place the power cord in a 
location where it can be seen at all time during the maintenance or service.

5.

Place a warning tag on the Main Power Inlet.

6.

Turn the shut-off valve for the pneumatic circuit to the 

OFF

position

7.

Lockout power in 

OFF

position.

8.

Put key (if any) in pocket.

9.

Clear machine of all personnel.

10. Test lockout by hitting 

RUN

button.

®

A NORDSON COMPANY

Ultra TT User's Guide

Version 1.2

7

Potential Pinch Hazard

WARNING!

There are several pinch points (indicated with yellow hazard stickers)

on this machine that should be avoided. Failure to do so while the machine is
operating may cause serious injury.

Содержание Ultra 325TT
















































































Отзывы:

Нет отзывов