manualshive.com logo in svg

EFD Ultra 325TT, Руководство пользователя, Страница: 60 / 79

Поделиться
Скачать
EFD Ultra 325TT Скачать руководство пользователя страница 60

®

A NORDSON COMPANY

Ultra TT User's Guide

Version 1.2

B. Lubrication of Cable

i. Use a lint-free cloth to wipe down cables and pulleys.

ii. Move the axis to home position i.e. X-axis to left most position and Y-axis to the rear

of the machine.

iii. Apply a light coat of grease (Molygraph #40-0037) to cables and pulleys.

iv. Move the axes to maximum travel limit i.e. X-axis to rightmost position and Y-axis to

front of the machine.

v. Repeat Step (iii).

vi. Move each axis back and forth for the entire length of the rail four (4) times.

vii. Wipe away any excess grease.

C. Tensioning of Cable

i. After lubricating the cables, it is a good idea to re-tension the cables.

ii. Locate the tension block.

iii. Loosen the two screws to the tension block.

iv. Move the axis back and forth for two (2) complete cycles.

v. Move the carriage back to approximately the center of the axes.

vi. Tighten the tension block, with the carriage at mid-travel.

vii. Replace covers.

60

Содержание Ultra 325TT
















































































Отзывы:

Нет отзывов