EFD Ultra 325TT Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 79

EFD Ultra 325TT Скачать руководство пользователя страница 14

®

A NORDSON COMPANY

Ultra TT User's Guide

Version 1.2

1.1.1

FRONT PANEL

14

P1 Gauge

&

Regulator

0 ~ 100PSI

LCD Menu

Scroll Knob

Emergency

Machine Off

(EMO)

Interactive

LCD

Interactive LCD

Soft Keys

Vacuum control

Ground Strap

Connector

RS232

PDA Connector

P2 Gauge

&

Regulator

0 ~ 30 psi

X/Y, Z/T

Jog Keys

Power
Button

P1:

0-100 psi pneumatic channel. To adjust the pressure, first unlock the pressure knob by pulling outward,

turn it to the right to increase pressure or left to reduce pressure. Push the knob inward to lock.

P2:

0-30 psi pneumatic channel. To adjust the pressure, first unlock the pressure knob by pulling outward,

turn it to the right to increase pressure or left to reduce pressure. Push the knob inward to lock

Vacuum control:

The vacuum is connected in parallel so both P1 & P2 channels can maintain a vacuum. To

adjust the vacuum pressure, turn the control knob to the left to increase vacuum and turn it right to decrease
vacuum.

Interactive LCD:

This is where you can view the current program selected, call up new programs, run tip

offsets or purge routines, pause or resume a program. The LCD also outputs user-defined messages along
with error messages. The arrow keys: X/Y, Z/T keys work in conjunction with the LCD that prompts the user
to either teach current position or teach new position for tip location at origin. The keys are selectable
between XY and ZT modes.

E-Stop:

The large red button with the yellow indicator shuts off power to all actuating devices such as

servomotors and pneumatic circuits. To reset power, you must turn the red button clockwise to release then
press the green button to restore power to the actuator. This button should only be used for real emergency
stops. If you want to abort a program, press the soft key directly beneath the word “abort” on the LCD panel.

«
...
12
13
14
15
16
...
»

Содержание Ultra 325TT
















































































Отзывы:

Нет отзывов