EFD Ultra 325TT Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 79

EFD Ultra 325TT Скачать руководство пользователя страница 62

®

A NORDSON COMPANY

Ultra TT User's Guide

Version 1.2

11

TROUBLESHOOTING

This section lists solutions to some possible difficulties an operator may encounter with the Ultra
TT System. If you encounter difficulties not listed in this section, or if the suggested solution does
not correct the problem, please contact your local EFD Ultra TT Representative. Alternatively,
complete our online Technical Request Form (

www.efd-inc.com/xyz/technical-form.html

) and our

Technical Support team will get in touch with you shortly.

62

WARNING!

Allow only qualified personnel to perform the following tasks.

Observe and follow the safety instructions in this document all other related

documentation. Failure to do so may cause serious injury to the user or

Symptom

Possible Cause

Recovery Procedures

1. The Power button has not been

Press the green Power button on

pressed.

the Control Panel.

2. Main Power Cable is

Check that the Main Power Cable

disconnected.

is connected to an AC source.

3. Main Power Circuit Breaker is

Turn ON the Main Power Switch at

OFF.

the rear of the system.

4. The EMO button has been

Turn the EMO button clockwise until

activated.

it pops out. Press the green Power
button on the Control Panel.

Table 11.1: System Power Troubleshooting

No power to major
system components

«
...
60
61
62
63
64
...
»

Содержание Ultra 325TT
















































































Отзывы:

Нет отзывов