manualshive.com logo in svg

Edwards nEXT200200, Инструкция по эксплуатации

Поделиться
Скачать
Edwards nEXT200200 Скачать руководство пользователя страница 10

8.9  Fail signal or standby signal not working. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   79
8.10  Yellow service LED is flashing a repeated sequence. . . . . . . . . . . . . . . . . . .   79
8.11  The red alarm LED is on. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   79
8.12  The red alarm LED is flashing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   79
8.13  Other problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   79
8.14  Flashing service codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   79
8.15  Decoding service status words. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   80
8.16  Controller run time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  81
8.17  Pump run time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   81
8.18  Pump cycles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   81
8.19  Bearing run time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  82
8.20  Oil cartridge run time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  82
8.21  Flashing error codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   82
8.22  Decoding system status words. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   83
8.23  Useful service information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   85

9.  Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  87

10.  Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   88

11.  Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   89

11.1  Return the equipment or components for service . . . . . . . . . . . . . . . . . . . .   89
11.2  Bearing and oil cartridge on-site maintenance. . . . . . . . . . . . . . . . . . . . . . .   90

12.  Spares. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   91

12.1  ISX inlet screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   91
12.2  Inlet strainer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   91
12.3  Inlet-flange seals and integrated inlet screens. . . . . . . . . . . . . . . . . . . . . . . .  91
12.4  NW16 and NW25 Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   91

13.  Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   92

13.1  Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   92
13.2  ACX air cooler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   92
13.3  WCX water cooler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  93
13.4  BX bakeout band. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   93
13.5  TAV vent valve and vent port adaptor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   93
13.6  VRX vent restrictor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   93
13.7  Vent port adaptor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  94
13.8  PRX purge restrictor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   94
13.9  C-clamp adaptor kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   94
13.10  Interface cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   94
13.11  TIC PC program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   95

Page 6

Содержание nEXT200200





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды