EcoSmart EcoWave EcoTouch Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 43

background image

EcoSource Low Voltage Installation

Step 2

Turn off power at EcoSource mounting location using a disconnect switch or breaker lockout/tag
out on appropriate breaker panel.

Step 3

Test that power is off by using a voltmeter.

Step 4

Remove the safety screw from the left side of the thermostat using the hex wrench. See Figure
13.

Figure 13: EcoSource Side View

Step 5

Separate the backplate from the thermostat: Use a flathead screwdriver to GENTLY press the
tab next to the screw hole to allow the thermostat to pop open. WARNING: Using too much
force can break the tab.

Step 6

For drywall  mounting instructions, go to Step 7.
For JBOX  vertical installation  instructions, go to Step 19
For JBOX horizontal installation instructions, go to Step 30

Thermostat wiring cannot touch or be placed in close proximity to the J7 pins! This can occur if
the wiring enters the thermostat from the J8 hole and is placed diagonally, directly over the J7

pins.

Drywall Mounting Instructions

•

Requires four 50 lb. EZ-Lock anchors and provided screws

Step 7

Hold backplate against wall at appropriate height. Using a pen, level-mark your 4 holes.

Step 8

Use appropriate drill for anchor and insert anchors into holes.

Step 9

Screw backplate to the wall and into the anchors. Re-check that it is still level.

Step 10

Strip the LINE wire back 0.25 inches.

Step 11

Cap the LINE wire with a wire nut or electrical tape.

Step 12

Cut the COMMON wire so the copper is flush with the insulation.

Step 13

Strip all wires except for COMMON back 0.25 inches.

Step 14

Verify the wiring now looks similar to Figure 14.

EcoWave Featur ing EcoTouch IO&M Guide

Telkonet, Inc.

For Use w ith Fir mw ar e Ver sion 2.x

20800 Sw enson Dr ive, Suite 175

EcoSour ce

Waukesha, WI 53186

Revision 2

(800) 380-9640

Page 15

w w w .telkonet.com

«
...
16
17
18
19
20
...
»

Содержание EcoWave EcoTouch












































Отзывы:

Нет отзывов

Похожие инструкции для EcoWave EcoTouch

Бренд: IDEAL Страницы: 16

Бренд: VDH Страницы: 4

Бренд: Verano Страницы: 20

Бренд: Axio Страницы: 4

Бренд: Danfoss Страницы: 2

Бренд: Mi-Heat Heizsysteme Страницы: 16

Lyric T6 Pro Wi-Fi

Бренд: Honeywell Страницы: 36

Бренд: NuTone Страницы: 2

Бренд: Seitron Страницы: 12

Бренд: CVS Health Страницы: 2

Бренд: IBP Страницы: 11

Бренд: Honeywell Страницы: 6

Бренд: Geevon Страницы: 2

Xtool 35 524 970 90

Бренд: Dornbracht Страницы: 32

Wezzer BASE L20

Бренд: Levenhuk Страницы: 26

Бренд: Hunter Страницы: 4

Бренд: Hunter Страницы: 40

Бренд: PEWA Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды