EcoSmart EcoWave EcoTouch Скачать руководство пользователя страница 38

Страница: 38 / 43

Troubleshooting

Problem

Potential Cause

Potential Solution

Occupant returns to room and finds it

too hot or too cold.

During an Unoccupied period, the

EcoSmart system allows the

temperature in the room to drift away

from the occupants’ setpoint.

Telkonet’s RecoveryTime technology is

enabled to return the room to the

occupants’ setpoint within a time

defined in advance by the property

manager (this varies by property, but it

usually between 8 and 20 minutes).

Advise the occupant to wait 8 – 20

minutes. (This is the typical range of

defined recovery times requested by

customers in most installations.)

“Sensor Down” message appears on

thermostat.

One or more sensors have lost

association to the thermostat.

Dispatch M aintenance to the room. Re-

associate all sensors via procedures.

Replace the batteries in all sensors

within the room.

Evaluate the wiring between each

sensor and the thermostat.

Occupant reports HVAC shuts down

while they sleep.

Sensor is not accurately detecting

occupancy. This is typically seen in

deployments where the bed placement

within the room was changed after

installation, such that the pillow area

of the bed(s) is further than 10-15 feet

from the sensor.

Assess the room, sensor placement,

and bed location(s). Verify that the

sensor(s) are deployed in accordance

with the Recommended Best Practices.

Corrective strategies may include:

M oving the sensor

Adding an additional sensor to

accommodate the new room

layout

Changing the room layout

Adjusting Sensor settings

(contact Telkonet to discuss

options)

Adjusting night delay (contact

Telkonet support for

assistance)

Occupant reports one mode

(heating/cooling) works but the other

does not.

Heat pump jumper is reversed or

changeover signal is backwards, or it

may be that the heat/cool jumpers are

reversed.

Correct jumper or changeover signal as

necessary.

EcoWave Featur ing EcoTouch IO&M Guide

Telkonet, Inc.

For Use w ith Fir mw ar e Ver sion 2.x

20800 Sw enson Dr ive, Suite 175

Appendix ATr oubleshooting

Waukesha, WI 53186

Revision 2

(800) 380-9640

Page 35

w w w .telkonet.com

Содержание EcoWave EcoTouch












































Результаты поиска

Содержание EcoWave EcoTouch

Отзывы:

Похожие инструкции для EcoWave EcoTouch

Бренды по названию

Популярные бренды

EcoSmart EcoWave EcoTouch, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание EcoWave EcoTouch

Отзывы:

Похожие инструкции для EcoWave EcoTouch

Бренды по названию

Популярные бренды