Eco Heating Systems CB 105 HW, Инструкция по установке, обслуживанию и эксплуатации

Страница: 97 / 147

E93.1803.901 HW 98
Lockout codes
Lock-
out
code
Error Description Cause Solving
0 E2PROM_READ_ER
ROR
Internal software error wrongly programmed BCU
or PB
reset BCU or replace BCU and or
display unit
1 IGNIT_ERROR Five unsuccessful ignition
attempts in a row no gas, wrongly adjusted
gas valve check gas supply and adjust gas
valve, reset BCU
2 GV_RELAY_
ERROR Failure detected in the gas
valve relay short circuit in coil of the gas
valve, water on wiring or gas
valve reset BCU replace gas valve or wir-
ing harness
3 SAFETY_RE-
LAY_ERROR Failure detected in safety re-
lay safety relay is not working
correctly reset BCU or replace BCU
4 BLOCKING_
TOO_LONG
Control had a blocking error
for more than 20 hours
blocking code active for
more than 20 hours
reset and check blocking code
5 FAN_ERROR_
NOT_RUNNING Fan is not running for more
than 60 seconds electrical wiring not correctly
connected, or Fan is mal-
functioning
Check wiring or replace Fan if not
solved check fuse on BCU or re-
place BCU
6 FAN_ERROR_
TOO_SLOW Fan runs too slow for more
than 60 seconds electrical wiring not correctly
connected, or Fan is mal-
functioning Check wiring or replace Fan if not
solved check fuse on BCU or re-
place BCU
7 FAN_ERROR_
TOO_FAST Fan runs too fast for more
than 60 seconds electrical wiring not correctly
connected, or Fan is mal-
functioning Check wiring or replace Fan if not
solved check fuse on BCU or re-
place BCU
8 RAM_ERROR Internal software error wrongly programmed BCU
or PB reset BCU or replace BCU and or
display unit
9 WRONG_EEPROM_
SIGNATURE
Contents of E2prom is not
up to date
out dated E2prom reset BCU or replace BCU
10 E2PROM_
ERROR Wrong safety parameters in
E2prom wrongly programmed BCU
or PB reset BCU or replace BCU
11 STATE_ERROR Internal software error wrongly programmed BCU
or PB
reset BCU or replace BCU
12 ROM_ERROR Internal software error wrongly programmed BCU
or PB reset BCU or replace BCU
13 APS_NOT_
OPEN Air pressure switch not
opening during pre-purge 0 electrical circuit is short cir-
cuited or APS is jammed check wiring or replace APS
14 APS_NOT_CLOSED
_IN_PRE_ PURGE
Air pressure switch not clos-
ing during pre-purge 1
no air transport to the
burner; flue or air inlet is
blocked or APS is jammed
or air signal hose not con-
nected to the air intake pipe
or water in hose
Check if there are any obstructions
in the flue or air intake, replace APS
if jammed, connect air hose to the air
intake pipe, remove any water from
the hose.
15 MAX_TEMP_ ER-
ROR
The external overheat pro-
tection is enabled or the
T_Supply sensor measures
a temp. of over Prot_Over-
heat_Temp - SGOver-
heat_Duplex_Tolerance for
a period of Max_Value_Pe-
riod
Burner door clixon tripped
because of overheating of
the burner door or the water
flow is restricted or back wall
thermal fuse has tripped be-
cause rear wall insulation
disc (combustion chamber)
is damaged or broken.
Check burner door gasket and re-
place burner door gasket and reset
clixon on burner door or check pump
and waterflow and replace pump or
increase water flow check also if
valves are closed or check if rear
wall fuse is broken if so replace and
also replace rear wall insulation disc
(combustion chamber).
16 FLUE_GAS_ ER-
ROR Flue temperature exceeded
the maximum flue tempera-
ture
There is no water in the heat
exchanger or flue gas sen-
sor is malfunctioning or heat
exchanger is overheated.
Check if flue sensor is working cor-
rectly if not so replace flue sensor.
Check waterflow if to low increase
waterflow.
17 STACK_ERROR Internal software error wrongly programmed BCU
or PB
reset BCU or replace BCU and or
display unit