Eagle ICA-D212-725, Инструкция по эксплуатации

Страница: 555 / 729

ICA-D212-725 (71)
Page 24 of 28
CHAPTER 71 – POWER PLANT SYSTEM (71-00-00)

COPYRIGHT

2007 BY DART AEROSPACE LTD.

THIS DOCUMENT IS PRIVATE AND CONFIDENTIAL AND IS SUPPLIED ON THE EXPRESS CONDITION THAT IT IS NOT TO BE USED FOR ANY PURPOSE OR COPIED OR COMMUNICATED TO ANY
OTHER PERSON WITHOUT WRITTEN PERMISSION FROM DART AEROSPACE LTD.
Revision: 5
Date: 12.06.20
71.4.3.2 Install tailpipe as follows:
71.4.3.2.1
Position tailpipe onto rear of
combustion section. Align dowel pins on rear
face of combustion section to matching indents
in face of mounting flange of tailpipe. Locate
band clamp and bolt to bottom and top
centerline of engine.
71.4.3.2.2
While tapping around band
clamp with mallet, torque clamp nut 100 to 130
inch-pounds.
71.4.3.3
Install igniters as follows:
71.4.3.3.1
Connect four igniter leads to
respective igniter plugs.
71.4.3.3.2
Tighten and secure with shear
wire (C-414).
71.4.3.4
Install bleed air adapter as
follows:
71.4.3.4.1
Remove four bolts attaching
bleed air adapter cover and remove cover
71.4.3.4.2
Install gasket supplied on
engine.
71.4.3.4.3
Position bleed air adapter on
bleed air tube with hose coupling nipple facing
the front of the engine. Bleed air fitting may be
positioned from level forward to 45 degrees up
as required to clear other engine accessories.
71.4.3.4.4
Install four washers and four
bolts,
71.4.3.4.5
Secure bolts in pairs with
lockwire (C-405).
71.4.3.5
Install engine mounting fittings
as follows:
71.4.3.5.1
Install mount fitting on left rear
side of engine.
71.4.3.5.2
Install four washers and four
bolts securing the fitting to the engine,
71.4.3.5.3
Torque bolts 160 to 190 inch-
pounds and lockwire (C-405).
71.4.3.5.4
Check trunnion mount bearings
prior to installation for 0.010 inch maximum axial
play between ball and race. If bearings play is
greater than these values, replace bearings,
71.4.3.5.5
Position the bearing on the
engine mount fitting. Install washer and nut.
71.4.3.5.6
Torque nut 160 to 190 inch-
pounds.
71.4.3.5.7
Install procedures for right side
mount fitting are identical to left fitting. Install
the right fitting using steps (1) through (3).
71.4.3.6
Install trunnion, cambox, and
bracket as follows:
71.4.3.6.1
Paint mating surfaces of
trunnion and engine with primer (C-201 or C-
204).
71.4.3.6.2
Place trunnion into position on
lower left side of engine,
71.4.3.6.3
Position oil pressure transmitter
and bracket on trunnion, the transmitter
mounting hole provision facing aft of engine,
71.4.3.6.4
Align lower bolt holes of bracket
and trunnion with mounting holes of engine.
71.4.3.6.5
Install two lower bolts with
washers through bracket and trunnion.
71.4.3.6.6
Position cambox on trunnion,
aligning mounting holes on cambox with upper
mounting holes of trunnion. Install two bolts with
two washers.
71.4.3.6.7
Torque mounting bolts 480 to
560 inch-pounds.
71.4.3.6.8
Secure bolt heads in pairs with
lockwire (C-405).