Eagle ICA-D212-725, Инструкция по эксплуатации

Страница: 78 / 729

ICA-D212-725 (11)
Page 3 of 19
CHAPTER 11 – PLACARDS AND MARKINGS (11-00-00)

COPYRIGHT

2007 BY DART AEROSPACE LTD.

THIS DOCUMENT IS PRIVATE AND CONFIDENTIAL AND IS SUPPLIED ON THE EXPRESS CONDITION THAT IT IS NOT TO BE USED FOR ANY PURPOSE OR COPIED OR COMMUNICATED TO ANY OTHER
PERSON WITHOUT WRITTEN PERMISSION FROM DART AEROSPACE LTD.
Revision:
6
Date: 13.08.26
11.0 PLACARDS AND MARKINGS
11.1 PLACARDS
Decals, stencils, and markings used on Model 212
helicopters are shown on Figure 11-1. The first
part of this figure shows sections, views, and
details on the helicopter. Subsequent parts of the
figure show detailed appearance, quantity, and
location of each unit by an item number. A heavy
black asterisk (*) in front of certain index numbers
indicates the item is required by government
regulation.
NOTE
The decals shown in detail views are typical for
helicopters being delivered at the time this manual
was published. Therefore, the decals shown may
be different than those originally supplied on any
other particular helicopter. The decals shown are,
generally, the decal which will be supplied when
replacements are ordered. In all cases, refer to
BHT-212-IPB or IPC-D212-725 for ordering
information and decal part numbers for a particular
helicopter.
11.2 DECALS – APPLICATION
MATERIALS REQUIRED
NUMBER NOMENCLATURE
C-233 Polyurethane Enamel
C-305 Aliphatic Naphtha
C-306 Toluene
C-349 Edge
Sealer
C-385 Isopropyl Alcohol
C-426 Masking Tape
C-516 Clean Cloth
NOTE
Receiving surfaces must be non-porous.
11.2.1 Remove dirt, grease, wax, or other
contaminants from the surfaces to be bonded, as
follows:
11.2.1.1
For non-metallic and painted
surfaces, clean with a clean cloth moistened with
aliphatic naphtha (C-305). Dry surfaces with a
clean cloth (C-516) before the aliphatic naphtha
(C-305) evaporates.
CAUTION
DO NOT ALLOW TOLUENE (C-306) TO MAKE
CONTACT WITH PAINTED OR NON-METALLIC
SURFACES. DAMAGE TO THE SURFACE MAY
OCCUR.
11.2.1.2
For bare metal surfaces, clean
with a clean cloth moistened with toluene (C-306).
Dry the surfaces with a clean cloth (C-516) before
the toluene (C-306) evaporates.
11.2.2 Apply the pressure-sensitive (adhesive-
backed) decal to the bonding surface, as follows:
11.2.2.1
Apply the decal at temperature
above 60°F (16°C) for best results. Otherwise,
first apply solvent (refer to manufacturer's
instructions) or isopropyl alcohol (C-385) to the
decal.
11.2.2.2
Remove the adhesive protection
from one edge of the decal with a quick smooth
movement.
11.2.2.3
Carefully align the decal in the
correct position.
11.2.2.4
Put the peeled edge of the decal
on the edge of the bonding surface and apply firm
pressure with your finger along the seam edge.
NOTE
For application of large decals, use a plastic
squeegee with a firm pressure.
11.2.2.5
While you continue to remove the
adhesive protection, apply finger pressure to the
remaining part of the decal until the entire decal is
applied. For the best result, hold the opposite
edge away from the surface until the entire decal
is applied.
11.2.2.6
Make sure there are no air
bubbles trapped under the decal. Otherwise,
make a hole in the bubble with a pin and press