Eagle ICA-D212-725, Инструкция по эксплуатации

Страница: 301 / 729

ICA-D212-725 (52
)
Page 50 of 54
CHAPTER 52 – DOORS AND WINDOWS (52-00-00)

COPYRIGHT

2007 BY DART AEROSPACE LTD.

THIS DOCUMENT IS PRIVATE AND CONFIDENTIAL AND IS SUPPLIED ON THE EXPRESS CONDITION THAT IT IS NOT TO BE USED FOR ANY PURPOSE OR COPIED OR COMMUNICATED TO
ANY OTHER PERSON WITHOUT WRITTEN PERMISSION FROM DART AEROSPACE LTD.
Revision: 4
Date: 11.06.01
0.50 in. (12.7 mm).
52.7.4.3.2.7 Remove all dust and foreign matter
from window mating area and from window
mounting flange.
52.7.4.3.2.8 Apply a 0.125 in. (3.18 mm) wide
bead of adhesive (C-308).
52.7.4.3.2.9 Position window to mounting flange,
align holes, and install screws, washers, and nuts.
CAUTION
WHEN CLEANING WINDOWS, USE ONLY
ALIPHATIC NAPHTHA, TYPE II (C-305). DO
NOT USE ALIPHATIC NAPHTHA, TYPE I, AS IT
WILL CLOUD WINDOWS.
52.7.4.3.2.10 Remove excess sealant from
around window using aliphatic naphtha (C-305).
52.7.4.3.3 Install lower crew door window (5) as
follows:
52.7.4.3.3.1 Guide window upward through slot
in bottom of door and into window channels.
52.7.4.3.3.2 Check progress of window through
opening in aft edge of door.
52.7.4.3.3.3 With window in a partially open
position, engage adjustable stop.
52.7.4.3.3.4 Install handle using three screws.
52.7.4.3.3.5 Install lower access door.
52.7.4.3.4 Install
forward crew door window as
follows:
52.7.4.3.4.1 Remove old sealant from mounting
flange with putty knife, spatula, or other suitable
tool.
CAUTION
WHEN CLEANING MOUNTING FLANGE AND
WINDOWS, USE ONLY ALIPHATIC NAPHTHA,
TYPE II (C-305). DO NOT USE ALIPHATIC
NAPHTHA, TYPE I, AS IT WILL CLOUD
WINDOWS.
52.7.4.3.4.2 Wipe and clean edging and
window with aliphatic naphtha (C-305).
52.7.4.3.4.3 If a new window is being installed,
trim window to final size. Position window into
mounting flange and drill mounting holes using
0.128 in. diameter drill.
52.7.4.3.4.4 Apply a 0.125 in. (3.18 mm) bead
of adhesive (C-308) around window.
52.7.4.3.4.5 Install 0.125 in. (3.18 mm) rivets
to secure window to crew door mounting flange.
52.7.4.3.4.6 Remove
excess sealing
compound from around edge of window using a
clean, lint-free cloth moistened with aliphatic
naphtha (C-305).
52.7.5 Passenger/Cargo Door Windows
(Doors Equipped with Push out Windows)
The passenger door windows are made of clear
acrylic material. The windows are installed in
metal frames with silicone rubber retainers and
are designed for emergency egress.
EMERGENCY PUSH HERE decals are installed
in each lower corner.
52.7.5.1 Removal
NOTE
Removal is not recommended unless required
by window or retainer damage. Procedures are
same for all push out windows.
52.7.5.1.1 Remove interior decor/trim as
necessary to gain access to window supporting
structure.
52.7.5.1.2 Using Mylar, Tedlar or similar tape,
mask off structure adjacent to window retainer.
The mask edge should be pressed firmly
against, but not on, retainer.