Dynapac PL2000S Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 228

background image

D 52

D PL2

000.

G

B

52

-168

-

1

0

.0

1

Levelling screen

The following settings can be
made from this screen.

- Call up program for setting

off at grading depth (F2)

- Changeover from manual

to automatic mode on the
left side of the vehicle (F3).

- Changeover from trans-

verse slope controller to
height controller (and vice
versa):
-(F4) = left side
-(F5) = right side

If there is a changeover from transverse slope controller to height controller, the LED
display of the keys alters at the same time on the switch panel as well as on the lower
control elements.

- Nominal value adjustment for levelling on the right side of the machine (F6)

The screen for setting the
length of approach relative to
grade is called up by pressing
function key (F2) :

Four setting values can be al-
tered:

- Grade, left side of machine

(1)

- Distance to cover before

reaching the preset grade
for left side of machine (2)

- Grade, right side of ma-

chine (3)

- Distance to cover before

reaching the preset grade
for right side of machine (4)

- Select the desired value using the cursor keys.

The selected value is underlined on the display panel.

- This function is started or interrupted using the START and STOP keys on the ter-

minal. The switched status (5) is displayed.

Terminal2.Tif/ 3290028.jpg

Terminal2.Tif/ 3290085.jpg

1

3

2

4

5

«
...
110
111
112
113
114
...
»

Содержание PL2000S





































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PL2000S

AZ7333 - Cd Personal

Бренд: Magnavox Страницы: 27

Бренд: Rolls Страницы: 4

Бренд: Denon Страницы: 104

Бренд: Samsung Страницы: 14

Бренд: Samsung Страницы: 17

Бренд: Samsung Страницы: 18

Бренд: Samsung Страницы: 18

Бренд: Samsung Страницы: 18

Бренд: Samsung Страницы: 18

Бренд: Samsung Страницы: 24

Бренд: Samsung Страницы: 24

Бренд: Samsung Страницы: 14

Бренд: Samsung Страницы: 21

Бренд: Samsung Страницы: 20

MCD-SF75 - CD YEPP

Бренд: Samsung Страницы: 15

Бренд: Samsung Страницы: 17

Бренд: Samsung Страницы: 18

Бренд: Samsung Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды