Dynapac CA270 Скачать руководство пользователя страница 12

Страница: 12 / 99

Safety - General instructions

ICA270-IN2EN1.pdf

2012-11-05

16. Hearing protection is recommended if the noise level exceeds 85 dB(A). The

noise level can vary depending on the equipment on the machine and the
surface the machine is being used on.

16. Hearing protection is recommended if the noise level exceeds 85 dB(A). The

noise level can vary depending on the equipment on the machine and the
surface the machine is being used on.

17. Do not make any changes or modifications to the roller that could affect

safety. Changes are only to be made after written approval has been given
by Dynapac.

17. Do not make any changes or modifications to the roller that could affect

safety. Changes are only to be made after written approval has been given
by Dynapac.

18. Avoid using the roller before the hydraulic fluid has reached its normal

working temperature. Braking distances can be longer than normal when the
fluid is cold. See instructions in the STOP section.

18. Avoid using the roller before the hydraulic fluid has reached its normal

working temperature. Braking distances can be longer than normal when the
fluid is cold. See instructions in the STOP section.

19. For your own protection always wear:

- helmet
- working boots with steel toecaps
- ear protectors
- reflecting clothing/high visibility jacket
- working gloves

19. For your own protection always wear:

- helmet
- working boots with steel toecaps
- ear protectors
- reflecting clothing/high visibility jacket
- working gloves

Содержание CA270




































































































Результаты поиска

Содержание CA270

Отзывы:

Похожие инструкции для CA270

Бренды по названию

Популярные бренды

Dynapac CA270, Инструкция по эксплуатации

Результаты поиска

Содержание CA270

Отзывы:

Похожие инструкции для CA270

Бренды по названию

Популярные бренды